The Course · Chapter 9 Beta

Chapter 9: Construction Basics and Environmental Issues

How a house is put together, and everything in it that can hurt someone

In this chapter

  • Two sessions, eight things you'll be able to do Codes and permits
  • Name the codes that direct construction in New York and explain permits, inspections, and the certificate of occupancy. The site
  • Apply New York's on-site well and sanitary waste requirements, and the factors that decide the best use of a site. Read a house
  • Name every component from the footing to the ridge board, and explain what each one carries. Framing
  • Distinguish platform, post and beam, and balloon construction, and say where the studs run in each. Identify on sight
  • Recognize roof styles, siding, window types, foundations, and the house styles common in New York. The major systems
  • Explain heating, cooling, ventilation, plumbing, electrical, insulation, and the warranties owed on them. Environmental law
  • Explain NEPA, the EPA's statutes, wetlands protection, SEQR, and the New York agencies that enforce them. Hazards and disclosure

Lesson 1

Codes, the Site, and the Shell

A basic knowledge of construction is what lets you have the first conversation, and know when to call a professional.

From Specification to Certificate of Occupancy

Planning, permits, codes, and the inspections that close a project out

A client will ask you what a certificate of occupancy is on your first new-construction deal. Another will ask why the addition needed a permit when the deck did not. You are not the builder and you are not the inspector. You are the person in the room who has to answer well enough to keep the deal moving, and who has to know the moment to stop talking and bring in somebody licensed to answer it.

Construction runs in a fixed order, and every step in that order produces a document. Learn the order and the documents come with it. Specifications, blueprint, permits, inspections, certificate of occupancy. Five steps, five pieces of paper, and each one is a question a buyer or a seller will eventually ask you.

Specifications are the written documents explaining the requirements for the scope of the work. Materials, standards, and the expected quality of the finished product. The specifications are written before anything is dug, because a builder cannot bid a job and an appraiser cannot appraise new construction until the quality, type and quantity of materials have been decided.

A blueprint is a detailed building plan used to evaluate the design, determine feasibility, and guide construction of the structure. Once the lot is chosen, the blueprint is what goes out to builders for quotes. Alongside it sits a materials list that settles the finish decisions one at a time. Hardwood or carpet over the subfloor. Which cabinetry, and whose. Those choices are in the price the builder gives, which is why a buyer who changes them mid-build changes the contract.

Permits come next, and permits are the step that surprises people. Local authorities review the specifications and the blueprints, and often a plot plan showing the proposed layout of the site and where the building will sit. A permit is an official government document acknowledging that the proposed work meets the department's standards and granting permission for the work to be performed. In some areas a single building permit covers the whole project. In other areas separate permits are issued for the building, the electrical, and the plumbing, and then separate inspectors follow each one.

Permits do a second job that matters more than the first. They prompt the government to monitor the project and follow up with inspections at each stage. A permit is not a fee you pay to be left alone. A permit is how the municipality knows to come and look.

A certificate of occupancy is issued after all inspections have been made and the property is deemed fit for occupancy. Under the New York State Uniform Fire Prevention and Building Code a certificate of occupancy is required in two situations: for all work for which a building permit was required, and whenever the general occupancy classification for a building is changed. For altered buildings, a certificate of compliance is issued instead.

THE CODES THAT DIRECT CONSTRUCTION IN NEW YORK

Building codes protect the public by setting minimum standards and requiring builders to use particular construction standards. Methods and materials. Sanitary equipment. Electrical wiring. Fire prevention techniques. New York State adopted the International Building Code, and several other codes are widely adopted alongside it: the Uniform Building Code, the National Electrical Code, and the Uniform Plumbing Code.

State minimum, local maximum

The state sets minimum building standards and local jurisdictions may set stricter ones. That sentence explains most of the confusion a licensee hears in the field, because a buyer moving from one town to the next assumes the rule travels with him. It does not. The floor travels. The ceiling is local.

Codes adopted and enforced locally generally allow older work in residential properties to stay in place, as long as the work was up to code when it was installed and is presently in safe condition. Remodel that space and the rule changes. If improvements are performed, all conditions must reflect the current code. A seller who says the wiring was fine in 1974 is telling you half of what matters. The other half is whether the wiring is in safe condition today, and once anyone opens the wall to remodel, the current code applies.

Builders should stay current on accessibility compliance under the Americans with Disabilities Act. When new and stricter standards are imposed, property owners may have to bring old buildings up to code. Fines and injunctions are the usual enforcement tools for these laws and codes.

The New York Energy Conservation Construction Code became mandatory in 2002. It sets minimum standards for energy efficiency in new commercial and residential buildings, to cut energy costs and to clean New York's air by reducing carbon dioxide emissions and the sulfur that causes acid rain. For residential buildings it requires more stringent insulation in electrically heated homes, reduced infiltration in fireplaces, more efficient thermostats including programmable ones, and basement insulation levels that vary by region and climate. For commercial buildings it mandates high-efficiency transformers and provides a special compliance path for two-piped hydraulic systems, which are common in New York.

Now the distinction that costs agents money. A building inspection is the process by which government authorities, usually state or local, ensure compliance with prevailing building codes. A building inspector is not working for your buyer. The building inspector does not tell a prospective buyer about potential problems with the building. The building inspector confirms the work meets current building standards, and then leaves.

CAUTION: Never let a buyer treat a passed building inspection as a clean home inspection. They answer different questions for different people. One asks whether the work satisfies the code. The other asks whether this house has problems the buyer should know about before closing. A buyer who skips the second because the first came back fine has bought a house nobody inspected for him.

Permit, inspection, certificate of occupancy

REMEMBER: A seller tells you the finished basement was done ten years ago by a friend in the trades. Which of the five documents would you ask to see first, and what does it mean if none of them exist?

The Site: Water, Waste, and Best Use

New York regulates what goes into the ground before anything goes on top of it

Everything in this screen happens before a foundation is poured, and every item on it can stop a sale. A buyer who cannot get water cannot live in the house. A buyer who cannot get a septic system approved cannot build on the lot. A buyer who learns after closing that the zoning forbids the use he bought the land for has a claim, and the person he blames is usually the licensee who did not ask.

The State of New York regulates water supply and sewage disposal systems serving subdivisions under Article 11, Title II of the Public Health Law and Article 17, Title 15 of the Environmental Conservation Law. Those two statutes are the frame. The numbers below sit inside it.

ON-SITE WELLS

The New York State Department of Health publishes Appendix 5-B, Standards for Water Wells, and the standards exist to keep well water from being contaminated. A well must be located so that adequate access for inspection, maintenance, repair, renovation, treatment and testing is provided. A well must be located where it is not subject to seasonal flooding or surface water contamination, or it must be built so floodwater cannot enter it. A well must be located up gradient of any known or potential source of contamination, unless the property boundaries, the site topography, the location of structures and accessibility force a different spot, and there are minimum horizontal separation distances from potential contamination sources. Acceptable construction methods are drilling, driving, boring, jetting, and excavating into an aquifer.

Two numbers carry the well. A well must have a minimum casing length running from one foot above finished grade to 19 feet below finished grade when the drilling is finished. It may exceed 20 feet if geologic conditions are an issue, and it may be completed at less than 19 feet if groundwater availability is an issue. And to supply an average household adequately, a well is expected to produce at least five gallons of water per minute.

Five gallons a minute is the number to memorize, because it comes back later in this chapter as the guideline for adequate water pressure inside the house. Same figure, two jobs.

SEPTIC SYSTEMS AND MUNICIPAL WASTE

Wastewater treatment systems exist so New York's rivers and streams are not polluted and the water marine wildlife needs stays usable. Approval from the Board of Health must be obtained before a septic system may be installed. Write that sentence down in that order. The approval comes first. A buyer who installs first and asks later owns a system he may have to dig up.

A residential property usually has one of two sanitary waste systems. A septic system includes a septic tank and a soil absorption system, and it acts as a sewage treatment system that moves wastewater to an underground storage area where solid waste matter decomposes. A municipal wastewater system drains wastewater from the house through pipes into a sewer, and the sewer carries it to a local wastewater treatment facility.

Section 75-A of the New York Public Health Law covers wastewater treatment standards in detail. Where sewage treatment systems are to be located on the watersheds or the wellhead area of public water supplies, the rules the State Department of Health enacted to protect those supplies must be observed. Where individual sewage systems overlay a drinking water aquifer, local health departments may set population density limits and minimum lot sizes. Subsurface treatment systems must be separated from buildings, property lines, utilities and wells, to keep the system performing, to permit repairs, and to reduce the effects of underground sewage flow.

Two more numbers decide whether a lot can take a conventional system at all. There must be at least four feet of usable soil above rock, unsuitable soil and high seasonal groundwater for the installation of a conventional absorption field. And soils with a percolation rate faster than one minute per inch are not suitable for subsurface absorption systems unless the site is blended with less permeable soil. Percolation rate is the rate at which water moves through soil, and a soil percolation test, a perc test, is what measures it.

NOTE: Faster is not better here, and that is the trap. Soil that drains faster than one minute per inch moves effluent through before the ground can treat it. A buyer looking at raw land in a rural county should have the lot perc tested before he is in contract, not after.

SITE USE, LOOK AT THESE BEFORE YOUR CLIENT BUYS, NOT AFTER

Six factors decide the best use of a site, and the textbook is blunt about why they matter to you. If a client buys a site and later finds that some factor prevents him from using the property as he intended, it can blemish a licensee's reputation and may bring potential liability for failing to use reasonable care to research the information for the client before the sale.

Drainage is the natural or artificial movement of water from a given area. Grading is the slope of the ground or the landscape area. Proper drainage and proper grading are how rainwater is directed away from a property, and they are the cure for damp foundations, wet basements, and the long list of water problems that follow both.

Landscaping is improving a property or land by adding plants, trees, bushes and retaining walls, or otherwise altering the contours of the ground. It provides privacy, shading and curb appeal. A developer who builds around existing mature trees, a creek or woods is adding value to the land rather than clearing it off.

Appurtenances are rights that go with real property ownership. They usually transfer with the property, and they may also be sold separately. Rights retained or sold separately change how a site can best be used. Subsurface rights sold off to someone else affect what can be built on that property from then on.

Shading depends on how the structure sits on the lot. A structure facing east takes a lot of morning sun. Bushes and mature trees shade well and cut heat, and shade lowers energy bills by lowering the overall temperature of a building. Large trees shading a roof can often reduce the internal temperature 8 to 10 degrees Fahrenheit, though the actual reduction varies with other factors.

Walkways carry a federal requirement. The U.S. Department of Housing and Urban Development sets minimum building standards for housing and mobile homes, and enforces the federal Fair Housing Act for minimum property standards for walkways. The Architectural Barriers Act of 1968 stipulates that buildings must be accessible to those with disabilities. HUD also requires all states and cities to have building codes for accessibility, walkways and paths included. Beyond that, some neighborhoods require a specific type of walkway, and the blueprint or site plan is where that is found.

Zoning and other regulated limitations on land usage are implemented to protect the health, safety and welfare of a community. Land use controls limit development and affect property values. Land may be worth more with an office building on it than with a house, and the zoning may simply not permit the office building. The better use and the permitted use are two different things, and only one of them is for sale.

Approval first, construction second

REMEMBER: A buyer is looking at four acres upstate with no municipal water and no sewer. Name the three site numbers you would want answered before he signs anything, and say who has to approve the septic system.

Anatomy of a House

The components, from the footing in the ground up to the ridge board at the peak

This screen is vocabulary, and vocabulary is the whole point. A client describes a problem in the words he has. Your job is to translate what he said into the component that is actually failing, so that you call the right professional and do not promise anything you cannot deliver. Learn the house from the ground up, because that is the order it is built in.

A footing, also called a footer, is the underground base, usually concrete, that supports the foundation. A trench is dug so concrete can be poured onto solid ground, which makes the footer wider at the bottom, and wider than the structure it will support. Footers go below the freeze line, the deepest depth the ground freezes in winter. Local building codes dictate the size and placement of footers based on the characteristics of the ground, the type of foundation, and the frost depth common in the area.

Foundation walls are the side walls that support the structure, typically poured concrete, concrete block, or brick. New York building standards require at least eight inches of visible foundation wall above grade, and grade is simply ground level.

The sill plate is the bottom piece of the frame, anchored horizontally to the foundation, and it provides the nailing surface for the floor or wall system. It is the first layer of wood that starts the construction of the house. Everything wooden in the building traces back to it.

Joists are long horizontal beams of wood or steel. Floor joists span the piers of a foundation. Ceiling joists span the load-bearing walls of a roof. Floor joists sit on the ledges or sills of the basement or foundation walls around the perimeter of the building, and they are usually supported in the center of the building by the girder.

A girder is the large main carrying beam, usually running horizontally, that supports the vertical loads. The girder sits on some type of support column, and support columns may be concrete, wood, metal, or block piers. Those piers in turn sit on a slab or footer. Lally columns are steel support columns filled with concrete, and they are for interior use only.

The subfloor goes over the joists. Studs stand on what the subfloor creates.

A stud, also called a wood-framing member, is a vertical beam that frames a structure. Drywall and siding attach to studs. Studs must be at least two inches wide, and when installed as part of a framing system they should not be less than two by four inches in load-bearing partitions. That last figure is the one to memorize.

The top plate closes the wall at the top of the studs, and the rafters bear on it.

A rafter is a sloped support beam that follows the pitch of the roof and holds the outer roof covering. The rafters are fastened to the roof ridge beam, the horizontal beam at the top of the roof, sometimes called the ridge board. Pitch is the degree of a roof's slope, and stated precisely, pitch is a roof's vertical rise in inches divided by its horizontal span in feet.

STRUCTURAL TIE-INS

Wall development begins with bearing walls, which are the walls that carry the load for the roof, the ceiling and the floors. Reinforcements made of wood for door and window placement are called headers, or lintels. Flitch beams, made of two or more timbers cut lengthwise and bundled together, provide additional support for the ceiling and the roof.

A bearing wall is the one a renovation client wants to remove. That is why the word matters to you and not just to the framer. A buyer standing in a kitchen saying he will open this up to the living room is describing a job that costs one number if the wall carries nothing and a very different number if it carries the floor above. You do not answer that question. You name it, and you say it needs an engineer or a contractor to look at.

THE ROOF EDGE AND THE SHELL

The eave is the lowest section of the roof, the part that projects beyond the side walls, and it protects the property from the elements. The soffit is the underside of an arch, beam, overhang or eave, and it is often ventilated to provide adequate airflow to the attic. The fascia is the panel or board facing the outer edge of the soffit. If the property has gutters, the gutters are fastened to the fascia. Fascia also acts as decorative trim to give the roof a finished look, and Victorian and Tudor homes often feature fascia board that gives them their distinctive look.

Sheathing is a structural covering, often plywood, placed over a building frame's exterior wall studs or roof rafters. On the roof, sheathing is added, then covered by roofing paper, then covered by roofing material such as asphalt shingles, one of the most common roofing materials used today.

Flashing is added once the roof is in place. Flashing covers joints where two or more types of materials join together, for the purpose of preventing water from penetrating the joint. The standard example is metal over the seam between a brick chimney and a shingle roof. When a client reports a leak near a chimney, a skylight or a valley, flashing is the first word out of your mouth.

The building envelope, sometimes called the building shell, refers to the exterior elements that enclose the interior. Walls, windows, floor, roof. The envelope is the boundary between conditioned air and outside air, which is why it is the thing insulation and the energy code are both aimed at.

Footing, foundation, sill, joist, stud, rafter

REMEMBER: Start at the bottom and name the components in order, out loud, without looking. If you stop before you reach the ridge board, start again at the footing.

Foundation Types

The structure everything else sits on, it has to be strong, and it has to be dry

The foundation is the basic structure on which the rest of the house sits. A typical foundation system is concrete slab, pier and beam, crawl space, or basement. The foundation supports everything above it, so it must be strong and it must be dry. Those are two separate requirements and a house can fail either one.

A basement is part of a house or building partially or entirely below grade, used to support the rest of the structure. Basements are at least one full story in height and are formed from space excavated before the house or building is erected. The walls of a basement sit on concrete footers and serve as the foundation for the structure. In most of New York a basement is what a buyer expects, and its absence is a question you should be ready for.

A crawl space is the unfinished space below the first floor of a house or other structure, less than a full story in height. A crawl space is most often accessed from an exterior scuttle so the structure can be serviced from beneath. In other cases a crawl space is the result of a pier and beam foundation, where the piers extend out of the ground less than a full story in height and support the weight of the structure.

Slab-on-grade construction is a concrete foundation built directly on the ground. A slab-on-grade house or building does not have a basement. More precisely, a concrete slab is a foundation made from a layer of poured concrete reinforced with steel rods, called rebar. In some parts of the country the concrete slab is common because of the underlying soil or simple local preference. In other markets the concrete slab is considered inferior. Know which of those two your market is, because it decides how the house prices against its comparables.

The footer is the underground base, usually concrete, that supports the foundation. A trench is dug so concrete can be poured onto solid ground, and that makes the footer wider at the bottom, and wider than the structure it supports. Wider than what it carries is the whole idea. A footer spreads the load out over more ground than the wall above it touches.

Footers go below the freeze line, the deepest depth the ground freezes in winter. Local building codes dictate how footers must be built, their size and their placement, based on the characteristics of the ground being built on, the type of foundation used, and the frost depth common in the area. Frost depth is a local number and it is why the same house detail is built differently in Buffalo and on Long Island.

Foundation walls are the side walls that support the structure, typically made of poured concrete, concrete block, or brick. New York building standards require at least eight inches of visible foundation wall above grade.

NOTE: Eight inches above grade is a New York number and the exam asks for it directly. It also has a reason behind it that makes it easier to hold: visible foundation is foundation that is not sitting in wet soil, and it is foundation you can look at.

Now the dry half. The foundation carries everything above it, so it has to be strong and dry. Proper drainage and proper grading direct rainwater away from the property, and that is the cure for damp foundations and wet basements. A buyer who smells a basement and asks what is wrong is often looking at a grading problem outside the house, not a wall problem inside it. You do not diagnose it. You know enough to say that water comes from somewhere and that somebody should find out where.

Below the freeze line, wider than the load

REMEMBER: Name the four foundation types and say which one has no basement by definition. Then say the two things a foundation has to be, and which one of them is fixed from outside the house.

Platform, Post and Beam, Balloon

Three framing types, the difference is where the studs stop

Framing is the basic load-bearing skeleton of a structure, and the interior walls, the exterior walls and the roof system attach to it. Framing also includes the solid support structure surrounding window and door openings. When the interior framing is finished you can walk the floor plan and feel the layout of the house before a single wall is closed in. There are three basic frame construction types, and they are told apart by one question. Where do the studs stop?

Platform construction, also called platform framing, builds the house or building one story at a time, with each story serving as a platform for the next. Studs are cut to the height of each story, with horizontal flooring and support across the top of them. The studs for the next story are then cut and attached to that flooring. Platform construction is the most popular method, and it is what a new house in New York is almost certainly framed with.

Post and beam construction, also called post and beam framing, supports the floor for higher stories and the roof on beams that sit on top of posts and the outside wall perimeter. With post supports, fewer interior walls are needed, which allows larger and more open rooms. The posts, beams and frame members are heavier than in other types of framing, and in wood they are often left exposed for decorative purposes. When a listing photo shows heavy exposed timbers holding up a ceiling, this is usually the reason.

Balloon construction, also called balloon framing, runs long studs up the entire length of the house, from the foundation to the roof. Horizontal studs called ledger boards are nailed to those tall studs to support the floor and roof joists. The wall never stops at a floor.

Balloon construction is common in older multi-story brick buildings and is rarely used today. It is no longer permitted as a construction method by most building codes, because of its poor fire-resistant design and the high cost of the long studs.

The fire problem is worth understanding rather than memorizing. A stud cavity running unbroken from the basement to the attic is a chimney with nothing in it. Fire that starts low travels the full height of the wall with no floor to stop it. Platform framing interrupts that path at every story, and the interruption is the safety feature.

NOTE: The exam sets platform against balloon and asks which one is no longer permitted in most codes and why. The answer is balloon, and the reason is fire, with the cost of the long studs as the second reason. Post and beam is the distractor, and post and beam is still built today.

You will meet balloon framing in the field anyway, because the rule stopped new construction and did nothing about the buildings that already exist. An older multi-story brick building upstate or in a city neighborhood may well be balloon framed. That is a renovation fact and a fire-safety fact, and it is a reason to have an inspector who knows the type.

Platform stops at each story; balloon does not

REMEMBER: Say the three framing types. Then say which one is most popular, which one is mostly prohibited, and which one lets you build a room with almost no interior walls.

Roof Styles

Hip and gable are the two most common; the rest you learn by sight

A roof style is the first thing a buyer sees and the first thing he names when he describes a house to you. Knowing the styles by sight is a small skill that buys you credibility in the first ten minutes of a showing, and it also tells you something about what the attic, the top floor and the maintenance are going to be like.

Gable is the pitched roof, the one most people picture: two slopes meeting at a ridge, with a triangular wall at each end. Hip is square or rectangular, and all four sides slope down to the walls, so there is no vertical gable end at all. Hip and gable are the two most common roof styles.

Gambrel has two different slopes on each side, and the lower slope is far steeper than the upper one. It is the barn roof, and the Dutch Colonial roof, and it exists because the steep lower slope buys usable headroom on the floor beneath it.

Mansard has four sides, each with two slopes, and the lower slope is nearly vertical and usually carries windows. The effect is the same as the gambrel's, applied all the way around: the top floor becomes a real floor instead of an attic.

Shed is a single flat plane sloping in one direction. It shows up on additions, on dormers, and on modern infill construction. Flat is almost level, with just enough pitch to drain, and it is the standard on New York rowhouses and on commercial buildings. Saltbox is a gable with one short slope at the front and one long slope running down the back.

NOTE: Gambrel and mansard are the pair the exam confuses on purpose. Both have two slopes per side. The gambrel has two sides. The mansard has four. Count the sides and the answer falls out.

Pitch is what all of these are variations on. Pitch is a roof's vertical rise in inches divided by its horizontal span in feet, and a steeper pitch sheds water and snow faster. In a state that gets the snow New York gets, that is not a decorative question.

Hip slopes on four sides; gable on two

REMEMBER: Picture the last three houses you walked past. Name the roof on each one, and say whether the top floor is usable space or an attic.

Siding and Cladding

Siding goes on over the sheathing, and its whole job is shedding water

Siding is the outer covering for a building's exterior walls, designed to shed water and protect the building from the elements. It goes on after the sheathing, the structural covering, often plywood, placed over the exterior wall studs. Siding is commonly made of vinyl, wood, steel or aluminum, and many other exterior coverings are available, including stucco, brick and stone.

Clapboard is horizontal wood boards, each one overlapping the one below it. It is the traditional finish across New England and the Hudson Valley, and it needs paint on a schedule. Board and batten is vertical boards with narrow strips, the battens, covering the seams, and it is the barn and farmhouse look.

Vinyl is the most common modern siding, chosen for low cost and low maintenance. It also appears in this chapter for a second reason: installing vinyl siding over a lead-painted exterior is one of the accepted ways of covering chipping lead paint rather than disturbing it.

Brick on a house is usually a veneer over the sheathing rather than a structural wall. It is durable and it is the dominant fabric of New York's rowhouses. Stucco is cement plaster applied in coats over lath or masonry. It seals tightly, and a tight seal is exactly why cracks in stucco matter: water that gets through a crack has nowhere to go but into the wall.

Wood shake and wood shingle are split or sawn wood shingles laid in courses. They weather gray, and they are the signature of coastal Long Island houses.

On a roof the sequence is the same idea with different materials. Sheathing goes down over the rafters, then roofing paper over the sheathing, then the roofing material over that, most often asphalt shingle.

NOTE: Siding is a water question before it is a style question. Every one of these materials works by sending water down and out. The failures are all at the joints, which is why flashing exists and why a licensee looks at chimneys, valleys and window heads rather than at the middle of a clean wall.

Sheathing first, then siding

REMEMBER: Which siding material is also a lead-paint remedy, and what is the one thing you must never do to a lead-painted wall before covering it?

Window Types

Buyers ask, and the answer sets their expectation about replacement cost

Windows come up on every showing, because windows are where a buyer feels whether a house is cold. You are not quoting replacement prices and you are not judging the glazing. You are naming the type, so that the buyer who wants an estimate asks a contractor for the right thing.

Double-hung has two sashes that slide vertically in one frame. It is the most common window in older New York housing, and it is what a buyer in a prewar building is almost always looking at. Casement is hinged at the side and cranked outward. A casement seals against its frame when it closes, so it is a strong energy performer.

Awning is hinged at the top and opens outward from the bottom, which means it sheds rain and can stay open in weather. Sliding windows glide horizontally on a track and are common in ranch houses and post-war construction.

Bay is three units angled out from the wall, which adds floor area and brings light in from three sides. Bow is four or more units set in a gentle curve, and like a bay it projects beyond the plane of the wall. Both are a feature a seller paid real money for and both are worth pointing out on a showing.

Windows matter to a buyer for three reasons and it helps to have all three ready. They are the largest heat loss in most older houses, which is why the Energy Code reaches them. They are expensive to replace in quantity, so a house with twenty original windows carries a number a buyer should know about before he is in contract. And in a landmarked district or a co-op, replacing them may not be the owner's decision at all.

Picture is a large fixed pane that does not open. Maximum light, maximum view, and no ventilation at all, which is a real consideration in a room with no other window. A dormer is a window set in its own roofed projection from a sloping roof, and the dormer is what turns dead attic volume into usable space. Cape Cod houses are full of them for exactly that reason.

NOTE: Ventilation is a code subject and windows are part of it. A room that a seller calls a bedroom needs to be a legal bedroom, and light and air requirements are part of what makes it one. When a listing describes a finished attic or basement room as a bedroom, that is a question for the municipality, not a question you answer on the spot.

Name the type; let the contractor price it

REMEMBER: Which window type seals tightest when closed, and which one gives you no ventilation at all?

House Styles You Will Meet in New York

Style drives buyer expectation, renovation cost, and which comparables you may use

Style matters commercially before it matters aesthetically. Style sets what a buyer expects for the money. Style drives renovation cost, because the same square footage costs differently to work on depending on how it is laid out. And style decides which sold properties you may fairly use as comparables, because a buyer shopping colonials is not competing for ranches.

Colonial is the symmetrical two-story box: center entry, evenly spaced windows, gable roof, bedrooms all upstairs. It is the default suburban form across most of the state, and its symmetry is the giveaway.

Cape Cod is a compact one-and-a-half stories with a steep gable roof, a central chimney, and dormers lighting the upper half-story. The half-story is the point, and it is also where the renovation money goes.

Ranch is a single story, long and low, with a shallow roof and an attached garage. It is the post-war suburban standard and it sells strongly to buyers who want no stairs. Split-level staggers living areas over three or more half-levels connected by short flights of stairs, and it is the style buyers either love or will not consider.

Victorian is ornate and asymmetrical: turrets, wrap-around porches, steep and complicated roof lines. Victorian and Tudor are the two styles the textbook singles out for prominent decorative fascia board, and on both of them the fascia is what gives the roof its finished look.

Tudor has steep gables, half-timbering over stucco, tall narrow windows, and that same prominent fascia board. Brownstone and rowhouse means an attached masonry townhouse on a narrow lot, a stoop up to the parlor floor, and a flat roof. It is the New York City type, and what a buyer owns in one varies by the building, so read the offering before you describe the interest.

CAUTION: An old style is not a defect and a new style is not a guarantee. A 1920s Tudor with a sound roof and updated systems is a better buy than a 2005 colonial with a wet basement, and a licensee who talks about age instead of condition is teaching a client the wrong thing to worry about.

Style sets expectation and comparables

REMEMBER: Name the two styles known for prominent decorative fascia board. Then name the style that has no stairs at all, and say who that matters to most.

Lesson 2

The Systems That Run the House

“This furnace looks old, how long do they last?” “What are those vents on the roof for?”

Insulation and R-Value

The parts of a structure that need insulating are the floor, the walls, and the ceilings

Insulation keeps a property warm in winter and cool in summer, and the parts of a structure that need insulating are the floor, the walls and the ceilings. New York regulates insulation requirements through the New York State Energy Code, which covers where insulation is installed and what materials are used, among other regulations.

Two terms, and students mix them up every year. R-Factor is a way to measure the insulating value, the resistance to heat flow through a material or an object. R-Value is the insulation's R-Factor multiplied by the amount of material. So the more effective the insulation, the higher the R-Value it will have.

R-Factor times material equals R-Value

Hold it as a sentence rather than a formula. R-Factor is how good the stuff is. R-Value is how good the stuff is, times how much of it you used. Double the thickness of the same material and you have not changed the R-Factor at all. You have changed the R-Value, and the R-Value is the number that shows up on the label and in the energy code.

FIVE TYPES, AND WHERE EACH ONE BELONGS

Blanket insulation often comes in a pre-measured width to pair with standard stud, joist or rafter spacing. It is made of a mineral fiber such as fiberglass, enclosed in a paper covering. It is the pink batting a buyer sees in an unfinished attic, and it goes in ceilings and in exterior walls.

Foamed-in insulation is sprayed into an area. It starts as a liquid and expands into a plastic solid, often a polyurethane mixture, and it works well for insulating irregularly shaped spaces. Anywhere the cavity is not a clean rectangle, foam is the answer.

Loose-fill or blown-in insulation is blown into an area, most often the attic space. It is made of fiber pellets or loose fibers and is good at filling small, tight areas.

Rigid insulation is commonly used on basement walls and comes in a variety of thicknesses. It is made of a fibrous material such as fiberglass or polyurethane.

Reflective insulation is used between roof rafters, joists or wall studs. Its reflective surface either contains or resists heat to keep a space warm or cool. It has one condition on it that the exam likes: reflective insulation should be exposed to an open air space to work properly. Pack it tight against something and you have wasted it.

NOTE: Match the type to the location and most questions on this topic answer themselves. Rigid goes on basement walls. Loose-fill goes in the attic. Blanket goes in walls and ceilings between standard framing. Foam goes wherever the shape is awkward. Reflective goes between framing members and needs an air space in front of it.

This is a money conversation with a client, not a trivia conversation. An uninsulated attic is the cheapest large improvement most owners can make to a heating bill, and a buyer standing in a cold house asking what is wrong is often standing under a ceiling with nothing over it. You can say that. You cannot say what it will cost or what R-Value the code wants here, because the code answer varies by region and climate, and the Energy Code sets basement insulation levels that vary by region.

Higher R-Value means better insulation

REMEMBER: Say the difference between R-Factor and R-Value in one sentence. Then name the type of insulation that fails completely if you install it tight against a surface.

How the Systems Run Through a House

Heat, water, waste and power, and the ventilation that keeps the air moving

Four systems run through every house and each one enters at one point and branches from there. Heat comes off the furnace or boiler in the basement and moves through ducts or pipes, and the flue carries combustion gases out. Water comes in from the main under pressure and goes to the heater and to the fixtures. Waste leaves by gravity through drains and the vent stack on the roof lets air into the system so the drains can run. Power arrives at the meter, goes to the panel, and leaves the panel as circuits.

Learn where each system enters and where it leaves. That is enough to have the first conversation with any client and enough to know which trade to call.

VENTILATION

Interior air can carry high levels of pollutants and irritants, including dust, pet dander and chemicals, as well as high moisture levels. These affect the health of the people living there and they damage the structure itself. Effective ventilation means both a controlled ventilation rate and a means of distributing fresh air to habitable spaces.

The number is 15 cubic feet per minute per person. Ventilation systems should be sized so the building has a minimum ventilation rate of 15 CFM per person, and that rate should be continuous while the property is occupied.

Natural ventilation is what a property relies on when it depends on windows and airflow through cracks in the building. A drafty property may still have no reliable source of fresh air, because natural ventilation also depends on temperature and wind, and outdoor ventilation cannot be controlled. That is when a system is considered.

Balanced ventilation uses two fans. One removes moist and polluted air and a second replaces that air with fresh air. Balanced ventilation can be achieved with or without heat recovery as part of the system.

Exhaust ventilation uses an exhaust fan to remove air from the property, and an equal amount of fresh air enters either through intentional wall ventilation openings or through specially designed windows. It may be preferred in areas with moderate climates.

Supply ventilation uses either a supply fan or the forced-air heating and cooling fan to deliver fresh air, and in some cases it can pressurize the property. It may be preferred during months requiring cooling.

Spot or source point ventilation is the bathroom and kitchen exhaust fan. These are generally operated intermittently for cooking and bathing, and they are not necessarily a substitute for occupant ventilation.

NOTE: The trap on ventilation is the bathroom fan. Spot ventilation handles a burst of moisture in one room. It does not deliver the continuous 15 CFM per person the building needs. A question that offers spot ventilation as the way to meet a building's ventilation requirement is offering you the wrong tool.

ELECTRICAL SERVICE, WHERE IT ENTERS

Utility companies supply power to buildings through power lines, and those cables are either underground or aboveground. A service drop is the aboveground supply line going from the service pole to a building. A service lateral is the underground power supply line. For the most part, homeowners are responsible for everything else, upgrading a breaker box being the standard example.

That division is worth saying plainly to a client, because it decides who pays. The utility owns the supply up to its point of delivery. The owner owns the rest. A buyer told the electrical needs work is being told about his side of that line, not the utility's.

Drop is above ground; lateral is below it

REMEMBER: Name the minimum ventilation rate and say whether the bathroom fan satisfies it. Then say which of the two service types you would expect on a new subdivision with no visible poles.

Heating and Cooling

Three heating systems, three furnace fuels, and how the unit gets sized

This is the system clients ask about most, because it is the system that breaks in January and the system that shows up on the utility bill every month. The heating system of a house is made up of several elements depending on what is in use: boiler, registers, radiators, furnace or heat pump, flue, thermostat, and ducts and ductwork. Depending on the fuel there may also be electrical connections, gas lines, or oil and fuel storage.

Solar and radiant heating are becoming popular, and there are many alternatives available. The three most common heating systems are hot water, steam, and forced warm air.

A hot water system consists of a boiler, pipes, and convectors or radiators, and it works by heating and cooling liquid. A boiler, typically in the basement, heats water and sends it to pipes running through the walls of the home. The pipes move the water to the convectors or radiators, which transfer the heat to the air and warm the rooms.

A steam system needs the same three things: a boiler, pipes, and convectors or radiators. Steam is produced in the boiler and moves through the pipes to the convectors or radiators, which transfer heat into the room. Steam systems are either one-pipe or two-pipe. In a one-pipe system, steam and condensation travel through the same pipe. In a two-pipe system they travel through different pipes. Steam systems are considered less effective than hot water systems and are often found in older buildings, which in New York means a great many of them.

A forced warm air system is what most buildings have today. The components are a furnace with a blower, a heat source, distribution ducts, and return air ducts. Air is heated in the furnace and moves through ductwork to warm each room, and cool air is recirculated through the return air ducts. When a buyer asks about central air, this is the system that makes it easy, because the ductwork is already there.

THREE FURNACE FUELS

An electric furnace consists of a cabinet, a blower, heating elements and controls, and resistance heating elements heat the air to warm each room. Most electrical heating in New York does not use a furnace at all. Each room is heated individually and has its own thermostat. That is called cellular construction, and the cost is not much higher than oil or gas.

An oil furnace consists of the cabinet, heat exchanger, burner, fire box and blower. Air is heated when oil is burned in a chamber, and the blower moves the air through the ductwork to warm the building. Oil means a tank, and a tank is a subject this chapter returns to in its environmental half.

A gas furnace consists of a cabinet, heat exchanger, blower, gas valve and burner assembly. Air is heated in a gas-burning chamber and a fan moves it through the ducts to heat the building.

AIR CONDITIONING

The components of an air conditioner are a condenser, condenser fan, compressor, evaporator and blower, and a liquid refrigerant. The compressor moves the liquid refrigerant to the evaporator, where it absorbs heat from air passing over the coils, and the cooled air is forced through the room. The condenser needs outside air to operate, which is why air conditioning units are found outside.

Air conditioning units are either cooled by air or by water, or by a combination referred to as evaporative cooled condensing units. Air-cooled units expel heat outside and are the ones most often used in residential construction. Water-cooled systems often use cooling towers. Evaporative systems are most commonly used in commercial construction.

SIZING, AND THE ONE CALCULATION ON THE EXAM

Sizing a furnace or an air conditioner is not just about square footage. The number of windows, the type of foundation, the amount of ventilation and how the house is insulated all go into it. What the sizing actually turns on is how many British Thermal Units the house loses per hour. A British Thermal Unit, the common measurement of heating capacity, is the amount of heat needed to raise the temperature of one pound of water by one degree Fahrenheit.

Take the textbook's example and follow it all the way through. A 2,000-square-foot house loses about 60,000 BTUs per hour. In theory it needs a 60,000 BTU furnace. Install exactly that and the furnace would have to run constantly, which wastes energy and wears the unit out. So HVAC specialists add 20 to 30 percent to their estimates. In this example the house gets an 80,000 BTU furnace installed.

Then the run time. Divide the BTUs lost by the BTUs the furnace has. 60,000 divided by 80,000 is 75 percent, so the furnace runs about 75 percent of the time. That is the whole calculation.

NOTE: Air conditioning calculations are different from furnace calculations, because additional factors are considered. Heat rises and tries to escape, so a less powerful air conditioner is needed. A question that applies the furnace arithmetic to a cooling load is testing whether you noticed.

HEAT PUMPS

Electric heat pumps are an alternative to traditional heating and cooling systems. Heat pumps are more energy efficient than furnaces, and only one unit is needed instead of two. The distinct disadvantage is that heat pumps are effective only in moderate climates, though more refined systems have been introduced in recent years and are an improvement over earlier ones, which lost efficiency once the outside temperature dropped below a certain level.

It has become common to combine a heat pump with a traditional forced-air system, which creates a dual system. Other variations include the air-to-air heat pump, which draws on the outside air even in winter as a heat source, and the geothermal heat pump system, which uses the outside ground temperature to convert to inside heating and cooling.

Moderate climate is the phrase to hold onto. Much of New York is not a moderate climate in February, which is exactly why the dual system exists.

One BTU raises one pound of water one degree

REMEMBER: A house loses 60,000 BTUs an hour and has an 80,000 BTU furnace. What is the run time, and why did the installer not put in a 60,000 BTU unit?

Plumbing and Domestic Water

Supply lines carry water under pressure; the drain and vent system carries everything else away

A plumbing system is piping, sinks, drains, toilets, tubs, vents, showers, valves, faucets, and a hot water tank that runs on gas or electric. The piping includes cold water lines, hot water lines, and wastewater lines. Gas lines are often included as part of the plumbing system. The idea that organizes all of it is this: supply lines carry water under pressure from the source, and water heaters are specially designed to retain that pressure when delivering hot water. Drain lines carry waste away by gravity.

PIPING MATERIALS MOST JURISDICTIONS ALLOW

Cast iron is used as drainage piping and is found in municipal water systems. Cast iron is incredibly durable and lasts for many years. The downside is that it can corrode from the inside, which means the outside of the pipe tells you nothing.

Galvanized is steel with a protective coating designed to extend its life. It is often used for water lines, and it cannot be used for gas lines.

Copper is ideal for water lines and is generally considered superior to other types of piping. It can be expensive, and it is very durable because it rarely if ever corrodes. Brass is rarely used any more because of its expense.

PVC is a type of plastic piping popular in plumbing construction and drainage systems. It is economical and resistant to rust and corrosion, and PVC pipe cannot be used for hot water, though other types of plastic piping can be.

PEX is a flexible cross-linked polyethylene piping, popular because it is resistant to bursting if the lines freeze. Plumbers can avoid using a lot of elbows and joints to make more continuous piping runs, and fewer joints means fewer places to leak.

NOTE: Two of these carry a prohibition and the exam likes both. Galvanized cannot be used for gas lines. PVC cannot be used for hot water. Learn them as the two things that cannot, and the rest of the list is descriptive.

WATER HEATING

Most water heaters in New York are tank-type heaters, in which water is continually kept heated and ready for use. Tank sizes start at 30 gallons, although most homes have a tank between 40 and 75 gallons. Units holding 30 to 40 gallons are typically found in one-bathroom homes, and tanks of 50 gallons or more are found in homes with two to three and a half bathrooms.

Tankless water heaters have become popular. They do not retain water in a traditional tank. Instead, water is heated by a heating coil when it is needed. Tankless heaters are more energy efficient because they do not heat water continuously, only when hot water is called for.

Tank size is a question a buyer asks with a family in mind, and the sizes above give you a real answer. A 40-gallon tank in a house with three full bathrooms is a morning problem, and it is a cheap thing to fix before it becomes a complaint about the house.

DOMESTIC WATER

Water comes into a building through a series of pipes, and where it comes from depends on where the property is. A metropolitan or suburban property usually draws on the public water supply. A rural property may depend on a well water supply. Water is brought into the pipes through pressure from the main water supply, and when repairs are needed a curb shut-off temporarily cuts off water to the house from the main.

Every licensee should know where the curb shut-off is on a listing, because it is the first question a plumber asks on a burst pipe and the first thing a buyer wants to be shown at a walkthrough.

PRESSURE, VENTING, AND TRAPS

Building codes offer standards for maximum and minimum water pressure, and a guideline for adequate water pressure is five gallons of water per minute. That is the same five gallons per minute a well is expected to produce for an average household. Same figure, two jobs.

Low water pressure usually comes from one of three things. Problems in the underground lines leading up to the house. Mineral deposits on the inside of a pipe. Or well pumps with low pressure. Pressure can often be restored by increasing pipe size, or by repairing or replacing clogged pipes.

Buildings need proper venting to keep harmful gases out of living spaces, and building codes set the standards for it. In plumbing, the vent system consists of pipes that provide airflow through the wastewater piping. The vent system connects to a pipe on the roof called a vent stack, and the vent stack releases gases into the air rather than back into the building. When a client asks what the pipe sticking out of the roof is for, that is the answer.

A drain trap keeps some water in the elbow of a pipe so fumes and gases from the sewer do not escape back into the drain. Older-style S-traps have been replaced in most building codes with P-traps, because P-traps are better at stopping the backflow of gases and fumes, and an S-trap's water seal can be broken more easily. When the water in an S-trap makes a gurgling sound, that is a sign the water seal is broken and a small amount of sewer gas has escaped back through the drain opening of the sink.

CAUTION: A gurgling drain and a sewer smell are not a cleaning problem. They are a sign that a water seal has failed somewhere in the system, and the gas coming back through is the thing the trap exists to stop. Tell the owner to have a plumber look at it and put it in writing.

LEAD PIPES

Older homes may have water lines made from iron, steel, lead or other galvanized materials. Lead pipes are extremely hazardous, because they can contaminate drinking water. There is no remedy other than replacement, and clients should be advised that lead pipes should be replaced.

Say that one plainly and never soften it. Lead in water is colorless, odorless and tasteless, so nobody finds it by tasting the water. Water from lead pipes should be considered non-potable. This is the same hazard the lead paint screen deals with later, arriving by a different route.

Supply is under pressure; waste runs by gravity

REMEMBER: Name the two piping materials with a flat prohibition on them and say what each one may not carry. Then say what a gurgling drain is telling you.

Electrical Systems and Mandated Warranties

Volts, amps, protection, and what General Business Law 36-A and 36-B guarantee

A building's electrical system is a wiring distribution box, a circuit breaker box and circuit breakers, fuses, lights and lighting fixtures and light switches, and wall outlets. Two measurements describe what is moving through all of it, and clients confuse them constantly.

Voltage is a measure of the force that pushes electricity through a wire. Most residential circuits operate at 110 volts, and larger appliances require 220-volt circuits. Amperage is the amount of electricity going through the wire, measured in amps. Most residential service is a minimum of 100 amps, although newer construction more typically requires 200-amp service. Standard electrical service in New York calls for a minimum of 200 amps.

Force and amount. Voltage pushes, amperage is how much arrives. Power consumption is measured in watts or kilowatts, and high-wattage items draw large electrical current.

That last point is where an old house gets dangerous. If wiring is too thin it can get hot as a device tries to pull more power through it. Existing wiring in older houses without updated electrical service often cannot handle microwave ovens, air conditioners and the other high-drain items common today. Worn or frayed wiring significantly reduces the wire's load capacity and increases the risk of fire.

THE PANEL AND THE PROTECTION

A structure's electric service panel often contains the main disconnect switch, which cuts power to the whole structure, as well as individual circuit breakers and fuses. The amperage capacity can usually be found on the main disconnect switch, and that number, 100 or 200, identifies the amperage capacity. It is a number you can read for yourself at a showing without touching anything.

Two devices protect against overloading a wire's capacity. A circuit breaker is a device, usually inside the electrical breaker panel or circuit breaker box, designed to break its electrical connection if an overload occurs. A fuse is a protective device for a wiring system containing a wire designed to melt and open the circuit when overheating occurs. A breaker resets. A fuse is consumed and replaced.

Most building codes require kitchens and bathrooms to have specially grounded outlets called ground fault interrupters, which turn off power at the outlet instantly if the device plugged into it gets wet, shorts out, or malfunctions. These outlets are usually required next to sinks and other potentially wet or hazardous areas.

THE NATIONAL ELECTRICAL CODE

The National Electrical Code provides for the safe installation of electrical equipment and wiring. It is a U.S. standard and is part of the Uniform Fire Code created by the National Fire Protection Association. In New York, the New York Board of Fire Underwriters provides inspection services to ensure that installations comply with the NEC.

As of 1962 the NEC required that new 120-volt household receptacle outlets for general-purpose use be both grounded and polarized. A grounded circuit is connected to the ground for safety, limiting voltage buildup and providing an alternate route for electrical current flow. A polarized outlet has one slot larger than the other, so items can be plugged in only one way. One side is hot, or live, and the other is neutral. Limiting the path of the electrical current reduces the risk of electrocution.

That 1962 date is useful in the field. Two-slot outlets with both slots the same size, in a house of a certain age, tell you the wiring is old enough to be worth an electrician's opinion.

WIRING MATERIALS

Aluminum cabling is a good conductor of electricity and is found in buildings constructed after 1965. It is also used in many power grids and high-voltage transmission lines, and it is less expensive than copper and weighs less. Copper conducts better than aluminum, is easy to bend, and can take a high degree of heat without substantial damage.

BX cable is armored cable, a grouping of wires wrapped in a metallic covering to protect it from damage. Romex is cable wrapped in plastic containing two or more conductors, relatively easy to install and cost effective. Conduit is electric wiring enclosed in a metal or plastic pipe, flexible or rigid, with rigid offering more protection. Greenfield is flexible conduit, and it is not designed to be used in rainy, wet or damp areas.

MANDATED WARRANTIES AND GUARANTEES

Homeowners run into problems during home improvement work and after a new house is finished. A contractor does not show up when he said he would. A plumbing problem appears a month after the owners move in. New York implemented General Business Law 36-A and 36-B to deal with both, and the two halves do different jobs. 36-A regulates home improvement contractors. 36-B sets the warranties a home builder must extend to a buyer.

General Business Law 36-A governs home improvement. A few important points of this law dictate that home improvement contracts exceeding $500 should contain the approximate dates when the work will begin and end and a description of the work to be performed, a notice to the owner from the contractor about mechanic's liens, a schedule of progress payments if needed, and a notice to the owner that the owner has until midnight of the third business day after the contract has been signed to cancel the contract.

36-A also provides penalties for fraud. An owner who signed a contract with fraudulent terms or statements may sue a contractor for a penalty of $500 plus attorney's fees in addition to other damages. Contractors who do not deposit funds into an escrow account, or provide a bond of contract of indemnity or an irrevocable letter of credit, are subject to a civil penalty not to exceed $250 per violation or 5 percent of the contract price, with the total penalty not to exceed $2,500 per contract.

General Business Law 36-B governs a new home, and the warranties are three numbers. One year for workmanship. Two years for plumbing, heating, electrical, cooling and ventilation systems. Six years for material defects.

One, two, six

Those three numbers are worth more to a buyer than almost anything else on this screen, and a licensee who knows them is useful in a real moment. A buyer of an eighteen-month-old house whose furnace fails is inside the two-year systems warranty. A buyer told by a builder that the warranty ran out after a year is being told something that is true of workmanship and false of the heating system.

CAUTION: The three-day cancellation right in 36-A runs to midnight of the third business day after signing, and it belongs to the owner in a home improvement contract. Do not carry that number across to anything else in this course. It is a home improvement rule.

REMEMBER: Say the three warranty periods and what each one covers. Then say which statute they come from, and which statute covers the contractor who is remodeling a kitchen.

Lesson 3

Environmental Issues and Property Concerns

A lake is worth more than a landfill, until you learn what has been going into the lake.

Environmental Protection at the Federal Level

The statutes behind every environmental question a client will ask you

A buyer choosing between a house beside a lake and a house beside a landfill takes the lake. Now change one fact. A company has been quietly using the lake as a dumping ground for waste byproducts. Nothing about the view changed and everything about the property changed. That is the whole subject in one example, and it is why federal and state regulations require specific details to be disclosed when potential environmental hazards could be present in or around a property.

For many years people pumped pollutants into streams, lakes and the air with little thought about how it contaminated the earth. Environmental laws were established out of concern over the deteriorating quality of the air, land and water. Seven federal statutes carry the weight, NEPA and six more after it, and a licensee should be able to say what each one does in one sentence.

NEPA AND THE ENVIRONMENTAL IMPACT STATEMENT

In 1970 the National Environmental Policy Act was enacted to declare a national policy encouraging productive and enjoyable harmony between man and his environment, to promote efforts to prevent or eliminate damage to the environment and the biosphere, to enrich understanding of the ecological systems and natural resources important to the nation, and to establish a Council on Environmental Quality.

NEPA requires federal agencies to prepare an environmental impact statement for any project that would have a significant effect on the environment. An environmental impact statement details a project's impact on energy use, sewage systems, drainage, water facilities, schools, and other environmental, economic and social areas.

NEPA's reach is wider than most students expect. It applies to all federal development projects, such as dams and highways, and it also applies to private projects that require a license or permit from a federal agency, or a federal loan. A private developer with a federal permit is inside NEPA.

THE EPA

Before 1970, environmental concerns such as air pollution, water, solid waste and radiation were handled by different federal departments, bureaus, committees and offices. Those entities came together to form one independent agency, the Environmental Protection Agency.

The EPA creates and enforces environmental protection standards. It helps others with environmental pollution problems through grants and other means. It assists the Council on Environmental Quality by suggesting policies and procedures for environmental protection. And it provides research on environmental issues, including the effect of pollution on the earth and methods for controlling it.

The Clean Air Act requires the EPA to develop air quality standards for existing pollutants and to establish air standards for new sources of pollution. It regulates air pollutant emissions, determines acceptable levels for emissions, and sets deadlines for compliance. The Act established the procedures for how the EPA and individual states work together to set and enforce standards. States are required to prepare a state implementation plan for meeting national air quality standards, and states are authorized to stop projects that interfere with clean air objectives.

Under the Clean Water Act, national water quality standards are determined by the EPA. The Act created a regulatory structure for the discharge of pollution into waterways and gave the EPA the right to enact control programs. It set up a permit system: anyone who wants to discharge pollutants from a point source needs a permit, and discharges with unacceptable amounts of pollutants are prohibited. Enforcement in the early years focused on specific pollutants and sources such as municipal treatment plants and industries. In recent years the focus has been on protecting clean waterways and revitalizing contaminated ones.

CERCLA, THE SUPERFUND

The Comprehensive Environmental Response, Compensation, and Liability Act, CERCLA, addresses what to do with closed or abandoned waste sites. It created mandatory waste-site requirements and established consequences for the release of hazardous materials at those sites. A tax was created on the chemical and petroleum industries, and that tax revenue was placed in a trust fund used for cleaning up out-of-control or abandoned hazardous waste sites where no clearly responsible party could be identified. Because of the trust fund, CERCLA is also known as the Superfund.

CERCLA gave the federal government broad authority to respond when hazardous materials are released or when there is a threat of release, and it authorized two types of response. Short-term situations require immediate action to remove hazardous materials because of serious life-threatening issues. Long-term situations require action to permanently or significantly reduce dangerous exposure to hazardous materials, where the danger is not immediately life threatening.

Here is the part that reaches into your transactions. CERCLA established that liability for contaminated property transfers to new owners. Read that sentence twice. Buying the land buys the problem. That is what forces potential buyers and lenders to conduct due diligence, an environmental assessment of the property to determine any potential liability, by having a consultant determine the property's integrity.

SARA, 1986

Closely related to CERCLA is SARA, the Superfund Amendments and Reauthorization Act. SARA amended CERCLA in 1986 as a result of the administration of the fund. SARA increased the Superfund to $8.5 billion and required review of the standards and requirements in state and federal environmental laws and regulations. It established new enforcement authorities, increased state involvement in administering the Act, and created new settlement tools and procedures. It stressed the need for permanent remedies and new treatment technologies for waste-site cleanup, broadened public participation in deciding how sites should be cleaned up, and required the EPA to revise its assessment of risk to public health and the environment at uncontrolled sites and how those sites are ranked for cleanup.

SARA also created the concept of innocent landowner immunity, which does not hold landowners liable if they did not create the contamination and were not present on the site when the title was taken, providing there is proof, preferably an environmental audit.

Innocent landowner immunity is the answer to the liability transfer CERCLA created. The two go together, so learn them in that order. CERCLA moves liability to the new owner. SARA carves out the owner who neither caused the problem nor was there when title passed, and who can prove it.

RCRA AND THE SDWA

The Resource Conservation and Recovery Act gave the EPA authority to control hazardous waste throughout its entire life cycle: generation, transportation, treatment, storage, and disposal. Hazardous and Solid Waste Amendments in 1984 required land disposal of hazardous waste to be phased out. Additional amendments in 1986 enabled the EPA to address environmental problems that could result from underground tanks storing petroleum and other hazardous substances. RCRA focuses only on active and future facilities, and it does not address abandoned or historical sites, which are covered by CERCLA.

The Safe Drinking Water Act established standards for water intended for human consumption, including the amount of contaminants permitted and how frequently public water sources are tested and reported. The Act requires public water suppliers to report violations to consumers. Public water supplies are tested for different types of bacteria, chemical pollutants and mineral levels.

NOTE: RCRA and CERCLA are the pair that gets missed. RCRA is the living site, waste being made and moved and stored right now. CERCLA is the dead site, closed or abandoned. Active and future goes to RCRA. Abandoned and historical goes to CERCLA.

DUE DILIGENCE, THE FOUR PHASES

An environmental assessment typically consists of four phases, and they run in order with a decision point at the end of each one.

Phase I is investigative. The property is inspected and records pertaining to it for a period of 50 years are reviewed. If no problems are found, the process may end here.

Phase II is testing, done to determine the problem if there is one and its severity. If contamination is found, the next phase begins.

Phase III is cleanup. Local, state and federal agencies and other organizations may participate in the cleanup effort. After cleanup is complete, Phase IV is initiated.

Phase IV is management of the site, and it includes routine checks to prevent new problems.

The phases are mostly a commercial and investment subject, and that is where a new licensee meets them. A residential buyer is unlikely to commission a Phase I. A lender on a commercial property will insist on one, and the deal will wait for it.

CERCLA moves liability; SARA carves out

REMEMBER: Say what each of the seven statutes does in one sentence each. Then say which one moved liability onto a buyer who did nothing, and which one gave that buyer a way out.

Wetlands, SEQR, and New York's Water Agencies

Where the state protects the ground, and who signs off on what

Wetlands can have a tremendous impact on the value of surrounding properties, and not just individual homes. Entire communities sit next to them. Wetlands are ecosystems where the land is permeated with water, commonly referred to as swamps, bogs and marshes. The water lies either on or near the surface of the land, creating a highly conducive environment for the growth of plants and wildlife. No two wetlands are exactly alike, and almost every state has some form of wetland.

Three benefits explain why the law protects them. Wetlands prevent flood damage by acting as a barrier between drier land, absorbing and slowing water that could overwhelm communities. They act as a filtering system, trapping nutrients and sediment that affect water quality and interfere with fish reproduction. And they provide habitat and shelter for wildlife and aquatic species.

People used to view wetlands as insect-infested places best converted to usable land. That view changed as the benefits became better understood, and because wetlands are beneficial, governments passed laws to protect them.

FEDERAL PROTECTION

Federally, wetlands are protected under Section 404 of the Clean Water Act, which deals with the dredging or filling of waters in the United States, wetlands included. Section 404 is intended to minimize adverse actions that could damage wetlands and other areas. The U.S. Army Corps of Engineers regulates and enforces Section 404, with the EPA having ultimate authority.

In some states the EPA has authorized state environmental protection agencies to work with the Army Corps of Engineers to enforce and monitor wetlands, and some states have passed their own wetland protection laws. New York has passed its own.

NEW YORK'S FRESHWATER WETLANDS ACT

The New York State Department of Environmental Conservation has established the Freshwater Wetlands Act and the Statewide Minimum Land-Use Regulations for Freshwater Wetlands under the Environmental Conservation Law of New York State. Local governments that voluntarily assume regulatory authority over their wetlands must implement and adhere to the standards outlined in those Acts. Variances can be requested by submitting a proposal to commissioners explaining the social and economic benefits that would result.

Two numbers set the boundary of protection in New York. A protected wetland must cover an area of at least 12.4 acres, or have unusual significant importance. And adjacent areas within 100 feet of the wetland may also qualify for protection if the area provides security to the wetland.

Read that first number carefully, because the exception inside it does most of the work in practice. Twelve and four tenths acres is the general threshold. A smaller wetland of unusual significant importance qualifies regardless of size. A buyer who has measured a marsh at eight acres and concluded he is free has concluded too early.

WHAT NEEDS A PERMIT AND WHAT DOES NOT

Some activities are not restricted and do not require a permit: trapping, occasional use of motor vehicles, maintaining existing structures, some agricultural activities, and establishing walking trails.

Activities that are not allowed or that require a permit are those that could permanently change or destroy the wetland habitat. Dredging. Draining. Filling. Grading. Clear-cutting. Altering a beaver dam. Constructing roads, bulkheads, dams, docks, buildings and parking lots.

CAUTION: Owning the land is not permission to alter the wetland on it. That is the single most common misunderstanding a licensee will hear on a rural listing, and repeating it back to a buyer is how a licensee ends up in the middle of a violation. The correct answer is always the same: the DEC maintains maps showing all protected wetlands, and those maps are available at the DEC regional office and other local government offices. Look before anybody promises anything.

The maps exist precisely so that this question has an answer before a contract is signed rather than after a garage is poured. To conform to the standards set by the Freshwater Wetlands Act, the NYSDEC maintains maps showing all protected wetlands.

SEQR, TYPE I AND TYPE II

When a person, an entity or a government agency wants to initiate a project in New York State, the project must undergo an environmental impact assessment. Examples include the construction of residential developments and roads, and work in wetlands and other bodies of water.

Projects requiring an environmental impact assessment are classified as Type I. The process for review is directed by the State Environmental Quality Review Act, and SEQR mandates that local governments consider the impact on the environment as well as the social and economic benefits when determining whether to proceed. Projects that do not require an assessment are classified as Type II, and examples include replacing existing structures and minor construction.

Type I means assess. Type II means no assessment needed. New development and work in the water land in Type I. Replacing what is already there lands in Type II.

WHO REGULATES THE WATER

Ninety-five percent of New York State's population gets its water from public supplies, and the New York State Department of Health is responsible for regulating drinking water. In cooperation with other agencies the NYSDOH ensures the quality and quantity of public water supplies, regulates the operations of suppliers, authorizes plans for new subdivisions, and sets standards for private water supplies and sewage systems.

Installation and approval of individual residential on-site wastewater treatment systems in New York splits between two agencies by size. The New York State Department of Health handles systems of less than 1,000 gallons per day. The New York State Department of Environmental Conservation handles systems of 1,000 gallons or more per day.

Residential properties with private wastewater treatment systems are regulated under Appendix 75-A by the NYSDOH, and local health department standards must meet or exceed the state-defined standards. The NYSDOH sets standards for sewage flows, soil and site appraisals, and appropriate separation distances from wells, streams, residences and property lines. Septic tank requirements are based on the number of bedrooms in the household and the results of percolation tests. Once the site has been perced, the system can be installed. Alternative wastewater treatment systems must be designed by a professional who oversees the construction of the system to make sure it is built according to plan, and local health departments ensure the standards are met.

PRIVATE WELLS

The NYSDOH also oversees private well drilling. Well drillers must be licensed by the National Ground Water Association or equivalent, and registered with the Department of Environmental Conservation. The Residential Code of New York State determines the distances wells must be drilled from a potential contamination source. Well drilling includes any excavation done to obtain water: drilled wells, dug wells, springs, and well points.

Homeowners must send well water samples to a lab for testing. That is the only way to determine whether the water is contaminated. The NYSDOH can assist owners of private water sources if the water becomes contaminated, and experts recommend testing private wells at least once a year for bacteria, mineral content and pH levels.

A buyer on well water should be told to test, every time, without being asked. It is cheap, it is the only method that works, and no one else in the transaction is going to raise it.

12.4 acres, or unusual significant importance

REMEMBER: Name the two agencies that split on-site wastewater systems and say what number divides them. Then say what a buyer has to do before filling a corner of a protected wetland on land he owns.

Lesson 4

Property Hazards and Your Liability

You are not required to be a technical expert, you are required to know the signs and say so.

Six Hazards to Recognize on Sight

External or internal, man-made or natural, and every one of them a disclosure question

A nuisance is anything that interferes with the owner's right of quiet enjoyment. By definition that means a nuisance originates from another person's property. A property owner cannot be a nuisance to herself. She can only be a nuisance to her neighbors.

If a nuisance is more or less permanent it is referred to as an external obsolescence, and it can affect property values across a neighborhood. Noise from an airport. The stench from a factory farm. Both make property less desirable and both contribute to a neighborhood's decline. A nuisance cannot contribute to a neighborhood or to property values in a positive way, by definition. It can be private, affecting a private individual, or public, affecting the public as a whole.

An environmental hazard is a situation with potential for harm to persons or property from conditions that exist outside or within a property, and depending on the circumstances an environmental hazard may also be a nuisance.

External environmental hazards exist outside the boundaries of a property and can have a significant impact on its value. Toxic substances in nearby landfills. Waterways with high levels of pollution. Thick smog from nearby factories. Less quantifiable ones still cause problems: proximity to nuclear power plants, or the presence of high-tension power lines. Whatever the science says, there is a strong perception among some buyers that these factors are undesirable at best and unsafe at worst, and perception moves price.

Internal environmental hazards exist within a property, and they can be as dangerous as external ones or more so. The good news is that owners and buyers have some power over fixing internal hazards, which means they can be minimized or eliminated. You cannot move a landfill. You can remediate a basement.

SIX YOU SHOULD RECOGNIZE WITHOUT BEING TOLD

Lead paint: peeling or chipping paint in a home built before 1978, and the soil beneath it where exterior paint has fallen. Asbestos: wrapped pipes, duct insulation, ceiling tiles, dangerous when friable and airborne. Underground tank: a buried fuel or chemical tank, which New York's disclosure form asks about directly.

Radon: enters through cracks in the foundation, uncovered sump pumps and crawl spaces, and is odorless and invisible. Septic system: a failing tank or absorption field contaminates groundwater and the wells that draw on it. Wetland: protected ground that limits what a buyer may build, and it does not always look like much from the driveway.

NOTE: Every one of those six is a disclosure question before it is a science question. You are not being asked to test, measure or diagnose. You are being asked to notice, to say so, and to make sure it reaches the disclosure form honestly.

Notice it, name it, get it on the form

REMEMBER: Walk the outside of the last house you showed. Which of the six could you have spotted from the yard, and which one would you only find by asking the seller a direct question?

Lead-Based Paint and Title X

The one federal disclosure a residential licensee touches on nearly every older listing

This is the federal disclosure you will handle more than any other, and it is the one new licensees get wrong most often. Learn it as a procedure with a date on the front of it, because that is how it works in practice.

Until 1978, lead was added to exterior and interior paint as a drying agent and for pigmentation. Lead pipes and solder were also commonly used in plumbing systems in homes and businesses prior to the 1930s. Research found that ingesting or inhaling lead or lead dust caused health problems in children and adults. Lead poisoning occurs through the nose and the mouth. It must be breathed in or ingested, and you cannot get lead poisoning by skin contact.

1978, the year lead was banned from paint

The human body cannot tell the difference between lead and calcium, so lead acts as calcium in the body and can stay in the bloodstream for weeks. From there it can be absorbed by the bones, as calcium is, and remain permanently. Lead causes serious and irreversible health problems, and that is why it is discussed so much in real estate and why disclosure is required. Early signs in children include chronic fatigue or hyperactivity, loss of appetite or weight loss, difficulty sleeping, irritability, and a reduced attention span. Adults face fertility problems, high blood pressure, nerve damage, memory loss and concentration problems, muscle and joint pain, and birth defects in their children.

Beyond the paint itself, lead reaches people two more ways in a house: water and soil. Lead present in water is colorless, odorless and tasteless. In older homes it is wise to be alert for lead pipes, and there is no remedy other than replacement. Water from lead pipes should be considered non-potable, undrinkable. Older pumps made of brass or bronze can leach lead into well water, and some wells were once packed with a lead collar, lead shot, or lead wool. Homes built before 1988 often have copper pipes soldered together with lead-based solder, which can leach into the water. Water from that type of piping is usually considered safe if the water is not stagnant for more than six hours, and in a home built before 1988 it is advised to let the water run for one to two minutes before using it for consumption.

There is one more pipe nobody thinks about. In urban locations with municipal water supplies, the pipe in the yard running from the home to the water main is the responsibility of the homeowner. When water pipes are replaced in older homes, the water main pipe is often overlooked, and it should be inspected to make sure it is not made of lead.

The other route is soil. Issues arise when lead-based paint begins to chip or flake. Paint peeling from the exterior of a property can fall into the soil and contaminate it, and then the soil can be tracked into the home and deposited as dust. That is how exterior paint becomes an interior problem, and it is why the soil under a peeling porch is part of the hazard.

WHAT TITLE X REQUIRES

The Residential Lead-Based Paint Hazard Reduction Act, known as Title X, requires sellers, real estate licensees, property management companies, and landlords to disclose known lead paint hazards for homes built before 1978. EPA and HUD regulations issued to implement those disclosures require four things.

Disclosure of any known lead-based paint hazard in the home, and of any reports available from prior lead tests. A pamphlet about how to protect families from lead in homes must be given to buyers and renters. Homebuyers have a ten-day period, or another mutually agreed to time, to conduct a lead paint inspection or risk assessment at their own expense. And sellers, landlords and real estate professionals must include certain language in sales contracts and lease contracts to ensure the disclosure and notification actually take place, language that is included in most standard board of real estate contracts.

10 days to inspect, at the buyer's expense

The pamphlet has a name and you should know it: Protect Your Family from Lead in Your Home, produced by the EPA. It explains the facts about lead hazards, how lead can be ingested, the associated health problems, the responsibilities of a landlord, seller or remodeler, and general information about remodeling or removal. Real estate agents are required to ensure seller compliance in providing the pamphlet.

WHOSE JOB COMPLIANCE IS

Sellers, landlords and real estate licensees share responsibility for ensuring compliance with the lead paint disclosure rules. According to HUD, real estate licensees must comply with the law if the seller or landlord fails to do so. Licensees are not responsible, however, if owners conceal information or fail to disclose it. As long as licensees inform the sellers or lessors of their obligations to disclose, they cannot be held liable.

That is a narrow protection and it is worth understanding exactly. The thing that protects you is informing the seller of the seller's obligations. Not assuming the seller knows. Not handing over a form. Telling the seller, and being able to show that you told him. A licensee who never mentions the obligation and then signs the agent's line has given away the only protection he had.

The penalty for failure to disclose lead hazards is a fine of up to $10,000 and up to one year in jail, plus triple damages. Brokers and licensees commonly use additional lead-based paint disclosure forms alongside the contract language, as a way to prove compliance with HUD and EPA requirements. For convenience, brokers and agents frequently use the HUD disclosure form.

THE HUD FORM'S THREE SECTIONS

The HUD disclosure form concerning lead-based paint is divided into three sections, and each one is signed or initialed by a different person. The Seller's Disclosure is where sellers disclose known lead-based paint issues and any reports. The Purchaser's Acknowledgment is where purchasers acknowledge whether they received any reports, the pamphlet, and the right to an assessment period, or waived it. The Agent's Acknowledgment is where agents acknowledge their role in compliance and affirm that they informed the sellers of their obligations.

The agent's line on the form reads that the agent has informed the seller of the seller's obligations under 42 U.S.C. 4852(d) and is aware of his or her responsibility to ensure compliance. Read that line before you initial it, every time, and make sure the thing it says you did is a thing you actually did.

EXEMPT FROM THE LEAD DISCLOSURE RULES

Zero-bedroom units and lofts

Leases under 100 days

Housing only for the elderly

Disabled housing, no children

Units found to be lead free

Houses sold by foreclosure

Two of those six carry a condition inside them and the condition is the whole answer. Housing for the disabled is exempt unless it is occupied by children. A rental unit is exempt only where it has been inspected and found to be lead free, which means somebody tested it. Zero-bedroom units are lofts and dormitories, places with no separate bedroom at all. Units leased for less than 100 days and houses sold by foreclosure are exempt outright.

CAUTION: Sellers are not required to test for or remove lead paint or other lead hazards. That one catches people who have learned the disclosure rules well. The duty is to disclose what is known, to provide the pamphlet, and to allow the inspection period. The duty is not to test, and it is not to remediate. A seller who refuses to test and refuses to pay for removal is doing something entirely lawful.

What happens if lead is found is decided by the contingency language in the purchase contract. The contract may allow a buyer or tenant to rescind if unacceptable levels of lead are found, or a seller or landlord may have the right to remove the lead. Other times lead hazards are negotiated as a price reduction, like any other property defect or contingency.

MANAGING LEAD THAT IS ALREADY THERE

The only way to find out for sure whether water, soil or paint is contaminated by lead is to send samples to a laboratory for testing. Lead paint in good condition should be left alone and painted over to seal it. The easiest way to deal with chipping or peeling paint is to cover it up, by installing vinyl siding over the exterior of a house or adding a thin layer of drywall to interior walls.

Surfaces with lead paint should not be sanded or scraped, because sanding and scraping release lead dust into the air. That is the single most dangerous piece of well-meant advice a licensee can give an owner who is trying to save money before an open house, and it turns a contained hazard into an airborne one.

Disclose, provide, allow, never test

REMEMBER: Say the four things Title X requires. Then say the two things a seller is not required to do, and the one thing that protects you as the agent if the seller lies.

Asbestos, Radon, and Carbon Monoxide

The three you test for, plus the rest of the man-made list

Hazards are external or internal, and they are also man-made or naturally occurring, and some are both. Asbestos, lead and electromagnetic fields occur naturally, and it is the use of these materials by man that made them hazardous. What matters to you is knowing how to identify a hazard and how to deal with it.

ASBESTOS

Asbestos is a fibrous material derived from a naturally occurring group of minerals, used widely from World War II for its insulating and its heat- and fire-resistant properties. It was embedded in cement and plastic, and used to insulate pipes and duct work in older buildings, and in ceiling tiles. Asbestos is no longer used in construction, and the U.S. Department of Health and Human Services continues to classify it as a known carcinogen.

Friable materials, which are easily crumbled or become powdery when manipulated by hand, are some of the most dangerous asbestos-containing materials. Friable is the word the exam wants and it is the word that matters on a walkthrough, because asbestos sitting undisturbed behind a solid surface is a different problem from asbestos crumbling off a pipe.

Inhaled asbestos particles become trapped in lung tissue or the digestive tract, and over time the accumulation causes inflammation and scarring. Asbestosis is a lung disease causing shortness of breath, typically considered an occupational illness because it is caused by extended inhalation of asbestos fibers. Mesothelioma is a form of lung cancer, also typically occupational, caused by extended exposure. It may be decades before an exposed person develops symptoms.

Three testing procedures determine the presence or level of asbestos. Air testing moves a measured amount of air across a filter and examines the captured particles under a microscope. Bulk sampling has a certified asbestos handler remove a small piece of the suspect material and send it to a laboratory. Wipe sampling gathers particles from a surface with a piece of filter paper.

There is real debate over whether existing asbestos should be removed or left alone. Because it is thought to be a problem only when it becomes airborne, some hold it is best not to disturb it, and as long as it is kept in good condition it is not a threat. Removal is expensive, must be done by EPA-licensed contractors, and is the only permanent solution.

If the asbestos is in good condition there are two ways of managing it in place. Encapsulation applies a sealant that penetrates the material's surface and prevents the release of fibers, though it makes future removal harder and must be inspected regularly as the encapsulant deteriorates. Enclosure isolates the material behind a sturdy, airtight barrier, and it is a possible temporary remedy.

The New York State Department of Labor regulates the installation, removal and enclosure of asbestos materials.

CAUTION: Removal by EPA-licensed contractors is not a formality and there is no do-it-yourself version of this job. An owner who pulls crumbling pipe wrap off a basement pipe over a weekend has taken a hazard that was sitting still and put it into the air his family breathes. A licensee who suggests it has handed out advice that harms the client and exposes the agent.

RADON

Radon is a naturally occurring radioactive gas that emanates from rocks, soil and water because of the decay of uranium. It is odorless, colorless and tasteless, and because it is radioactive it has been identified as a cancer-causing agent. Indoors it can build to a dangerous level, especially in newer homes built to be more airtight. Lung cancer is the primary concern of extended exposure, and the Surgeon General has issued an advisory about it.

Radon enters a home from the ground, usually through cracks or holes in the foundation, and it can also creep in from uncovered sump pumps and crawl spaces. Its presence varies from location to location and from house to house, so one house might have a radon problem while another on the same street does not, and levels within a house vary with weather and time of year. It is recommended that every house in a radon-prone zone have a radon test every two years.

For a small fee, New York residents can request a home radon test kit from the New York State Department of Health, and kits can also be purchased at most home improvement stores, then sent to a certified lab for results. The other common method is a continuous electronic radon monitor, which costs more, is more accurate, and should be set up by professional certified testers. It is also more tamper resistant, which is why continuous monitors are typically used for pending real estate transactions.

The New York Property Condition Disclosure Statement asks if a property has ever been tested for radon. If a test has been conducted, a copy of the test results should be attached to the statement. Attached. Not summarized, not characterized, not left in a drawer.

The remedy is usually cheap, which is worth telling a nervous buyer. Purging a house of radon gas is relatively inexpensive, often less than the cost of eliminating termites. With low levels, sealing cracks may be enough. With higher levels it may be necessary to install a fan or blower to move fresh air through the house, and to vent the radon. Remediation systems should be installed by an experienced, licensed company, and testing should be performed afterward and checked periodically over the years.

CARBON MONOXIDE

Carbon monoxide is a natural byproduct of fuel combustion, a colorless, odorless gas released as fuel sources break down to produce heat. It is emitted by furnaces, space heaters, fireplaces, water heaters and stoves. When these appliances function properly, small regulated amounts are emitted and dissipate. When they malfunction, unacceptable levels can be released, and larger amounts can also be released when ventilation is inadequate. Carbon monoxide stops the blood from carrying oxygen through the body, and overexposure causes dizziness, nausea, headache, slowed response time, blurred vision, drowsiness, unconsciousness, and death.

New York law requires a carbon monoxide alarm in all new and existing one- and two-family dwellings, in multi-family dwellings including condominiums and cooperatives, and in rentals having any fuel-burning appliance, system, or attached garage.

The placement rules are specific and they are tested. An alarm must be installed on each story containing a sleeping area, and it must be within 15 feet of the sleeping area, so multiple alarms may be needed to keep every sleeping area within that distance. An alarm must also be installed on each story that contains a carbon monoxide source. The alarm must be clearly audible in all sleeping areas over background noise with all intervening doors closed.

One date splits the equipment requirement. Homes built before January 1, 2008 are permitted to have battery-powered carbon monoxide alarms. Homes built after that date are required to have the alarms hard-wired into the building with a battery back-up source. New York City requires all rental properties to have a carbon monoxide detector.

An owner with an attached garage should never leave a car running in it. Even with the garage door open, carbon monoxide can enter the home at deadly levels.

AND THE REST OF THE MAN-MADE LIST

Underground storage tanks store heating oil, gasoline, chemicals and hazardous waste, and New York's property disclosure form requires sellers to disclose the presence of any underground storage tanks or wells. The EPA has enacted tougher standards, imposing additional steps owners and property managers must take to protect tanks against corrosion, spills, leaks and overfills. What was once ordinary practice for storing fuel in rural areas is now an expensive process of proving a tank does not leak, or digging it up and removing it.

Some tanks are exempt from federal regulations: tanks holding less than 110 gallons; tanks on farms and residential properties storing less than 1,100 gallons of motor fuel for noncommercial use; heating oil tanks where the fuel is burned at the location; tanks aboveground or at ground level, including ones in basements or tunnels; and septic tanks and tanks that collect storm water and wastewater.

Exempt from federal regulation is not the same as exempt from disclosure, and where a state law is stricter the stricter law prevails. In New York the Department of Environmental Conservation and the Hazardous Substances Bulk Storage Program provide the guidelines and controls, and the state requires tanks to be certified by an environmental engineer in order to be filled. A tank is also an external hazard as easily as an internal one, because a leaking tank on a neighbor's land can contaminate your client's property.

In 2007, Section 242 of the Real Property Law was amended to require sellers to inform buyers, prior to a sale, of the existence of any uncapped natural gas wells of which the seller has actual knowledge. Actual knowledge is the standard, and the disclosure is owed before the sale. Capping a natural gas well could cost a new owner thousands of dollars he never planned for.

Chlorofluorocarbons are chemical compounds containing chlorine, fluorine and carbon atoms, known to deplete the ozone layer. Sold for years under the trademarked name Freon, they were used as a coolant in refrigerators, air conditioners and dehumidifiers, and as a propellant in aerosol cans. Use began to be banned in the 1970s. Hydrochlorofluorocarbons replaced them, still release some chlorine, and are considered by the EPA a class II ozone-depleting substance being phased out in turn. Hydrofluorocarbons replaced those, because they contain no chlorine. Owners and property managers must comply with Clean Air Act rules on disposal and coolant leaks or face substantial fines.

Urea-formaldehyde is a clear chemical used in manufacturing, found in particleboard, plywood paneling, carpeting and ceiling tile adhesives. The biggest concern is urea-formaldehyde foam insulation, which can be blown into an existing structure, and the EPA now recommends UFFI not be used in residential homes because of potential health risks. Exposure can cause shortness of breath, asthma, wheezing, and skin and eye irritation, and it causes cancer in animals and is suspected of causing it in humans. The fumes dissipate over time, so insulation installed years ago should not pose a health risk now.

Polychlorinated biphenyls are organic compounds manufactured mainly as cooling and insulating agents for transformers and capacitors. They are persistent organic pollutants, difficult to break down, so they accumulate in the environment and in the body. They have been proven to cause cancer in animals and are therefore considered a carcinogen in humans. The amount of allowable PCBs in water supplies is 0.5 parts per billion, a standard set by the EPA.

Electromagnetic fields are invisible fields produced by electrically charged objects. Small household equipment produces small fields and is not usually a problem. High-tension power lines, transformers and secondary distribution lines create larger fields, suspected as a cause of hormonal changes, cancer and behavioral abnormalities, and the evidence for those risks is controversial and in some cases contradictory. The real concern for a licensee is not the health issue but the public's perception of it. Properties near power lines are stigmatized, and stigma reduces value. Congress's Office of Technology Assessment recommends a policy of prudent avoidance: test for field strength, find which appliances and wiring emit the strongest fields, and reduce exposure by increasing distance from the sources.

Methamphetamine labs are found in homes, apartments, motels and cars, and the cooking process leaves a dangerous residue along with toxic byproducts and fumes. The residue contaminates floors, ceilings, walls, carpeting, vents and blinds, and personal property such as clothing and toys. Because it permeates the property it lingers unless a professional cleaner removes it, and some houses have been demolished. Toxic byproducts are often poured down the drain or into the soil outside, so the property can become a small toxic waste site. There are currently no federal disclosure laws on meth.

Poor air quality creates problems for the people inside a building. Sick building syndrome is where people suffer headaches, fatigue, nausea, sore throat, and nose and eye irritation only while in a building with poor air quality. Legionnaires disease is different, caused by airborne bacteria typically distributed by unclean air conditioning systems, and it can be deadly. Poor air quality is usually found in buildings sealed for energy efficiency without adequate ventilation, and the best remedy is to improve airflow throughout the structure.

Friable, odorless, colorless, no warning

REMEMBER: Name the one thing that makes asbestos dangerous, the two places carbon monoxide alarms must go, and the standard a seller must meet before he has to disclose an uncapped gas well.

Mold, Pests, Groundwater, and Your Liability

The naturally occurring hazards, and what the licensee actually owes the client

Environmental hazards are not always created by man. Mold and termites can have extremely destructive effects on a property, and both arrive without anyone doing anything wrong. What follows is how to recognize them, and then what the law actually asks of you when you do.

MOLD

Mold is a fungus that can grow anywhere and on any organic material. To grow, mold requires three things: moisture, oxygen, and a food source. Take away any one of the three and mold stops, which is why every real remedy in this subject is a moisture remedy.

A leaky roof that goes undetected, or serious water damage, creates a perfect atmosphere for mold growth. New construction creates a different version of the same problem, because a tightly sealed home lets moisture stay trapped inside. If mold is not found in time it can consume the substance it is growing on.

Some molds produce toxic substances known as mycotoxins. One of these is stachybotrys, black mold, which is greenish-black and grows on materials with high cellulose content such as drywall, ceiling tiles, and wood that is chronically moist. Mold can grow behind the surface of walls or wallpaper, which means the absence of visible mold proves nothing.

Not all molds are equal. Some are dangerous to humans and some are not. Mold can produce allergens that trigger wheezing, eye and skin irritation and a stuffy nose, and for some people mold causes asthma attacks. Suspected health issues include chronic fatigue, flu-like symptoms, and digestive, immune system and neurological problems.

The signs are things a licensee can see and smell on an ordinary showing. Visible mold growth. Plumbing leaks. Leaking roofs or windows. Strong, musty odors. Water stains on ceilings, walls or floors. Warped wood. Cracked or peeling paint. Peeling drywall tape. Clogged gutters. None of those is a diagnosis. Every one of them is a reason to say something.

NEW YORK'S MOLD LAW

The EPA has not specifically required mold disclosure or set standards to measure contamination. New York has gone further. In January of 2016 the New York State Mold Evaluation and Remediation Law went into effect, requiring licensing of all mold assessors and remediation contractors, issued by the New York State Department of Labor.

A person who conducts home inspections as part of a potential real estate transaction must also be licensed as a mold assessor if the inspection report is to include an assessment of mold conditions in the subject property, meaning an inspection intended to discover mold as well as the conditions that facilitate mold.

And the provision with teeth. The law prohibits a person licensed to perform mold-related services from acting as both the mold assessor and the mold remediation contractor on the same property.

CAUTION: One firm cannot both find the mold and sell you the cure. That is the conflict the 2016 law was written to stop, and a licensee who refers a client to a company that does both has recommended an arrangement New York prohibits. Ask the question before you make the referral: are you the assessor or the remediation contractor on this job?

There is no proven method of protecting a client from unwittingly ending up with a mold-contaminated property. There are steps that help: advising homebuyers to purchase separate mold protection insurance policies, having the property inspected specifically for mold by a specialist, and adding a mold protection clause to the standard purchase contract. Owners also have to maintain the property to prevent mold growth in the first place.

PESTS

Rodent and insect infestations cause major physical damage to a property, and the approach that works with a client is empathetic and proactive. Licensees should personally check the credentials of the companies they suggest, and it is always wise to recommend three or more.

The most common termite found in homes is the subterranean termite. Most infestations are relatively easy to identify by a trained technician or home inspector, and caught early they are treatable, while infestations that run for years can threaten the structural integrity of a home. Termites are hard to detect because they work underneath the wood surface and leave no sawdust. They hollow out the wood and leave the surface intact, so tapping a suspicious area to hear whether it sounds hollow is one test. The other is the foundation, where termites leave mud tubes, typically one-quarter to one inch wide, running from the ground to their access point.

Carpenter ants can be just as destructive, chewing into wood and creating a living habitat that causes damage. A carpenter ant looks like an ordinary ant, only very large. Black, or black and red, one-quarter to one-half inch long. They typically get in through openings in the foundation, and the signs are sawdust and slit-like holes in wood, especially around windows and doors. Remediation at the colony source is the preferred treatment.

Bees need a beekeeper before they need an exterminator. Licensees should never try to resolve bee problems on their own, because there can be more than 50,000 bees in one hive or nest. Beekeepers often save the colony and the property and usually cost less than an exterminator.

Bedbugs are small, flat, brownish insects about a quarter-inch long that feed mostly on human blood, and they have made a comeback in recent years, New York City very much included. They are usually detected by tiny blood stains and droppings on mattresses, box springs, upholstered furniture and baseboards. Getting rid of them almost always requires a licensed pest management professional.

New York State law requires insect damage or infestations to be disclosed. If a seller thinks there may be an insect problem, it is the licensee's responsibility to be proactive and counsel the seller to have the problem exterminated before marketing the home. Taking care of a problem and disclosing it beats negotiating around it, and it beats concealing or failing to disclose a latent defect by a very long way. Written documentation and receipts should be kept.

New York City landlords must tell prospective tenants in writing if an apartment has suffered a bedbug infestation within the past year, or if there has been a bedbug problem in the building during that time. The form is the DBB-N, Owner's Notice to Tenant Disclosure of Bedbug Infestation History.

GROUNDWATER

Groundwater is found in subterranean crevices or spaces and is naturally occurring, but most groundwater contamination comes from man-made sources. Dumping toxic waste contaminates underground water and the water supply. Contamination also comes from faulty septic tanks, leaky underground storage tanks, contaminated soil washed into lakes, rivers and streams, and toxic surface spills. Groundwater can also be contaminated by naturally occurring elements such as radon, lead and arsenic.

Contaminated groundwater reaches people who use private wells, and many public water systems use groundwater as a source. New York does require the seller to disclose the source of the water supply, whether a well, private, or municipal.

LIABILITY, AND WHAT YOU ACTUALLY OWE

Property owners are held to a higher standard than ever on environmental hazards. Where property is found to be contaminated, not only the past producers and dumpers can be held liable, but so can an innocent, current owner. Current and past owners might be required to pay cleanup costs even if they did not contaminate the property or know of the contamination. The law specifically includes liability for owners who knew or should have known of the contamination. Even a lender in a management capacity can be held liable.

Sellers are generally not held liable if they, in good faith, did not know adverse conditions existed. That could change, because some sellers have recently been held liable for environmental hazards they did not know about. What is settled is this: sellers must disclose any known hazard, and in some situations it is appropriate to call in experts to evaluate the situation.

Now your part, stated exactly as the textbook states it. Real estate licensees are not required to be technical experts with regard to environmental issues. They do need to understand environmental issues and know how to look for signs of trouble. They also need to stress the need for sellers to be honest and thorough when completing disclosure forms.

And here is where a licensee gets caught. Improper disclosure can result in a real estate agent being held responsible, if it is decided the agent should have known, or helped to conceal information. Should have known is the phrase to sit with. It does not ask what you knew. It asks what a licensee in your position, looking at what you were looking at, ought to have picked up.

Other real estate professionals, appraisers in particular, must make an extra effort to be aware of potential environmental hazards, because the value of a property and of properties in the immediate area or an entire neighborhood can be severely affected. When in doubt, an expert should be contacted.

Know the signs, say so, and call an expert

REMEMBER: You are not the expert. Say in one sentence what you are actually required to do about environmental hazards, and name the standard that makes an agent responsible for something he did not know.

What to Carry Out of Chapter 9

Eight things, and the numbers inside each one

This chapter covered two subjects that look unrelated and are not. How a building is put together, and everything in it that can hurt somebody. They belong together because the same client asks about both, usually in the same afternoon, and because most of the hazards in the second half live inside the components in the first half.

CODES AND COMPLETION

Building codes set minimum standards, and New York State adopted the International Building Code. States set the minimum and local jurisdictions may be stricter. A building inspection ensures compliance with prevailing codes, and a building inspection is not a home inspection: the building inspector does not tell a buyer about problems with the building. A certificate of occupancy issues after all inspections and once the property is deemed fit for occupancy, required for all work needing a permit and whenever the occupancy classification changes. Altered buildings get a certificate of compliance. The New York Energy Conservation Construction Code has been mandatory since 2002.

THE SITE

A well is expected to produce at least five gallons per minute, with casing running from one foot above finished grade to 19 feet below. Approval from the Board of Health must be obtained before a septic system may be installed. A conventional absorption field needs at least four feet of usable soil above rock, unsuitable soil and high seasonal groundwater, and soils percolating faster than one minute per inch are unsuitable for subsurface absorption unless blended with less permeable soil. Six factors decide the best use of a site: drainage, landscaping, appurtenances, shading, walkways, and zoning.

FOUNDATION AND FRAMING

Footers go below the freeze line and are wider than what they support. Foundations are concrete slab, pier and beam, crawl space, or basement, with at least eight inches of visible foundation wall above grade in New York. Framing is the load-bearing skeleton, and there are three types: platform, which is the most popular; post and beam; and balloon, which most codes no longer permit because of its poor fire-resistant design and the cost of the long studs. Studs should not be less than two by four inches in load-bearing partitions.

ROOF AND EXTERIOR

Rafters follow the pitch and fasten to the roof ridge beam, and pitch is vertical rise in inches divided by horizontal span in feet. Hip and gable are the common styles, with mansard, shed, gambrel, flat and saltbox behind them. Sheathing goes over the studs and rafters, then roofing paper and roofing material on the roof, or siding on the walls. Flashing covers the joints where two materials meet. The eave projects beyond the side walls, the soffit is its underside and is often ventilated to air the attic, and the fascia faces the outer edge of the soffit and carries the gutters.

INSULATION

R-Factor measures insulating value, the resistance to heat flow through a material or object. R-Value is that R-Factor multiplied by the amount of material, so the more effective the insulation, the higher its R-Value. Five types, each with a home: blanket, foamed-in, loose-fill or blown-in, rigid on basement walls, and reflective between framing members, which must face an open air space to work. New York regulates insulation through the New York State Energy Code.

THE MAJOR SYSTEMS

Heating is hot water, steam, or forced warm air, and furnaces are electric, oil, or gas. A British Thermal Unit is the heat needed to raise one pound of water one degree Fahrenheit, and run time is BTUs lost divided by BTUs available. Ventilation runs at a minimum of 15 cubic feet per minute per person. Piping is cast iron, galvanized, copper, brass, PVC or PEX, with galvanized barred from gas lines and PVC barred from hot water. Five gallons a minute is the guideline for adequate water pressure. A service drop is aboveground and a service lateral is underground, and standard electrical service in New York calls for a minimum of 200 amps. General Business Law 36-A governs home improvement and sets what a contract over $500 must contain, and 36-B warrants a new home for one year on workmanship, two years on plumbing, heating, electrical, cooling and ventilation systems, and six years on material defects.

ENVIRONMENTAL LAW

The EPA creates and enforces environmental protection standards. NEPA requires an environmental impact statement for any federal project, or private project needing a federal license, permit or loan, that would have a significant effect on the environment, and it established the Council on Environmental Quality. The Clean Air Act sets air quality standards and requires state implementation plans. The Clean Water Act sets water quality standards and a point-source discharge permit system. CERCLA created the Superfund and transferred liability for contaminated property to new owners, which is what forces due diligence. SARA amended CERCLA in 1986, raised the Superfund to $8.5 billion, and created innocent landowner immunity. RCRA covers hazardous waste through its life cycle at active and future facilities, while abandoned sites fall under CERCLA. The Safe Drinking Water Act governs water intended for human consumption. Wetlands are protected federally under Section 404 of the Clean Water Act, enforced by the Army Corps of Engineers with the EPA holding ultimate authority, and in New York under the Freshwater Wetlands Act, with protection generally reaching wetlands of at least 12.4 acres.

HAZARDS AND DISCLOSURE

A nuisance interferes with the right of quiet enjoyment and therefore comes from someone else's property; a more or less permanent nuisance is external obsolescence. The man-made hazards are asbestos, carbon monoxide, CFCs, electromagnetic fields, lead, methamphetamine, urea-formaldehyde, underground storage tanks, and uncapped gas wells. The naturally occurring ones are mold, radon, groundwater contamination, and pests. Title X requires disclosure of known lead hazards in housing built before 1978, the EPA pamphlet, and a ten-day inspection opportunity, and sellers, landlords and licensees share responsibility for compliance.

THE NUMBERS, IN ONE PLACE

Gather the figures, because the exam asks for them without context. Five gallons per minute, twice: the yield a well is expected to produce, and the guideline for adequate water pressure. Nineteen feet of well casing below finished grade, from one foot above it. Four feet of usable soil for a conventional absorption field. One minute per inch, the percolation rate past which soil is unsuitable. Eight inches of visible foundation wall above grade. Two by four inches, the minimum stud in a load-bearing partition.

Then the systems figures. Fifteen cubic feet per minute per person for ventilation. One BTU raises one pound of water one degree Fahrenheit, and an installer adds 20 to 30 percent to the calculated loss. One hundred ten volts on most residential circuits and 220 for larger appliances, with a New York minimum of 200-amp service. One year, two years, six years under General Business Law 36-B, and $500 as the contract size above which 36-A's contract terms apply.

And the environmental figures. 1978 for lead in paint and the ten-day inspection period that follows from it. 12.4 acres for a protected New York wetland and 100 feet for the adjacent area. Fifty years of records in a Phase I. January 1, 2008 for hard-wired carbon monoxide alarms, and 15 feet from a sleeping area. January 2016 for New York's mold law. 2007 for the Real Property Law amendment on uncapped gas wells.

WHAT ACTUALLY TRANSFERS TO THE JOB

Four habits come out of this chapter and they are worth more than any single number in it. Know enough construction vocabulary to name what a client is pointing at, so that you call the right trade and describe the problem accurately when you do. Know which hazards are visible from the yard and which ones only surface if you ask the seller a direct question, because the second group is where deals die. Know that your duty is to notice, to say so, and to make sure the disclosure form is completed honestly and completely. And know the moment to stop talking and bring in somebody licensed to answer, because that moment arrives in almost every transaction, and the licensees who get hurt in this subject are the ones who talked straight through it.

You are the one who notices

REMEMBER: Pick the three numbers from this chapter you are least sure of. Go back to the screen each one came from. Then say all three out loud with what they measure attached, because a number without its unit is worth nothing on the exam and less than nothing in the field.

You Be the Judge: The Peekskill Patch-Up

Twelve violations and one lawful act, in a single listing

This is an issue-spotting exercise and it is the hardest thing in the chapter, because nothing in the story announces itself. Read it once for the shape of it. Then read it again slowly, with this chapter open in your head, marking every sentence where somebody does something, says something, or fails to do something. Marking is all you do on the second pass. Judgment comes after.

Rosa lists 44 Sprucewood Road in Peekskill, a shingled colonial built in 1962. The kitchen ceiling and the porch rails are flaking paint. Rosa hands the buyers, the Ferrantes, a contract and tells them they have “three days to get a lead inspection done if you really want one.” She never gives them the EPA pamphlet, and she signs the agent's line on the HUD disclosure form without ever telling the seller, Mr. Okonjo, that he has any obligation at all. Mr. Okonjo says he will not test for lead and will not pay to remove any of it; Rosa passes that along and moves on. Then she tells him the cheapest fix is to have his nephew sand the porch rails down and repaint them before the next open house.

Walking the two-acre lot, Rosa notices a rusted fill pipe near the garage, the 550-gallon heating oil tank the seller mentioned is still buried out there, and a capped-looking wellhead behind the treeline that Mr. Okonjo admits is an uncapped gas well from the 1980s. Rosa leaves both off the property condition disclosure statement because “nobody asks about that stuff up here.” A radon test done last spring came back at a level the lab flagged; Rosa checks the radon box on the disclosure statement but detaches the lab report, telling the Ferrantes the number “doesn't mean much either way.”

The basement smells musty. Rosa recommends Hudson Valley Mold Group, who inspect the property, write the mold assessment, and then quote and perform the remediation themselves the following week. She also tells Mr. Okonjo the crumbling grey wrap on the old basement pipes “is just insulation, have your nephew pull it off in a weekend and bag it.” Upstairs, the house was rebuilt in 2010 after a fire; there is a single battery-powered carbon monoxide alarm screwed to a joist in the basement and nothing on the second floor, where all three bedrooms are. Rosa tells the Ferrantes the house is fully compliant.

The back acre is a marshy 14-acre wetland that the NYSDEC map shows as protected. Rosa assures the Ferrantes they can fill the low corner and put up a detached garage and gravel drive, “because it's your land, no permit needed for your own property.” Finally, when the Ferrantes ask about the two-year-old furnace the builder installed during the rebuild, Rosa tells them the builder's warranty ran out after twelve months and they are on their own now.

Twelve violations are buried in that story, and one lawful act is planted in it to catch you out. Find the acts first, then name the rule each one breaks. In that order, because a rule recited without a fact attached to it is not an issue you spotted, it is a rule you remembered.

Twelve violations, one lawful act

A method that works on a fact pattern this dense. Take one paragraph at a time. In each paragraph ask three questions. Who acted. What exactly did they do or fail to do. Which rule from this chapter is that. If you cannot name the rule, you have found something that bothers you rather than something you can prove, and the two are different.

The first paragraph is about lead paint and it contains five separate items. Work it against the four things Title X requires, the three sections of the HUD form, and the rule about disturbing lead paint. One of the five items in that paragraph is the planted lawful act, and it looks as wrong as everything around it. Finding it is worth as much as finding any violation, because the working version of this skill is telling a client that something is permitted when it is permitted.

The second paragraph is about disclosure of what is buried and what was measured, and it carries three items. One turns on something New York's disclosure form asks about directly. A second turns on a standard in the Real Property Law, so ask yourself what the seller knew and what the statute requires once he knows it. The third item is not a failure to check a box. It is what happened to a document after the box was checked, and the rule about that document is a sentence with one word in it that decides the answer.

The third paragraph carries three items and they come from three different places in the chapter. One is a New York licensing law from 2016 with a prohibition inside it about who may do two jobs. One is advice about a material that is safe until somebody disturbs it, given to exactly the wrong person. And one is a compliance claim about a device, where the date the house was rebuilt matters as much as where the device was installed. Check the date against the equipment rule, and check the placement against the story rule.

The fourth paragraph has two items and both are answers a licensee gave with confidence. One is about what an owner may do to protected land, and the sentence that makes it wrong is the reason the licensee gives rather than the act itself. The other is about how long a builder's obligation on a new system lasts, and it is a number from General Business Law.

NOTE: When you finish, sort what you found into three piles. Clearly a violation. Clearly lawful. Cannot tell from these facts. The third pile teaches you the most, because for each item in it you have to name the missing fact that would move it into one of the other two. A licensee who can name the missing fact is a licensee who knows what to ask the seller.

Then do the harder half. Take the item you were least sure about and argue the other side of it out loud, as though Rosa is across the table and has a reason for what she did. If you cannot build that argument at all, go back to the screen the rule came from, because you have memorized a phrase rather than learned a rule.

Watch also for the moments where Rosa is confident. Every one of her mistakes is delivered as reassurance. The house is fully compliant. Nobody asks about that stuff up here. It is your land, no permit needed. The number does not mean much either way. A licensee who says less and checks more would not have made a single one of them, and the phrase that would have prevented most of the twelve is short: let me find out.

One more thing worth seeing before you move on. Almost none of the twelve is a technical failure. Rosa is not accused of misreading a radon measurement or misidentifying a mineral, and nobody expects her to do either. Every item is a moment where she answered a question she should have routed to somebody else, or shortened a period the law fixes, or left something off a form, or gave an owner advice that turned a contained hazard into an airborne one. That is what liability in this subject actually looks like, and it is exactly why the duty in this chapter is to notice, to disclose, and to call an expert.

Name the fact, then name the rule

REMEMBER: Count what you found before you check anything. Fewer than twelve means going back to the paragraph you read fastest, and it is almost always the one about the basement.

Check yourself

12 questions on this chapter. Pick an answer to see whether it is right and why.

Key terms

Percolation test
A test of how fast soil absorbs water, used to approve a septic absorption field; soils faster than one minute per inch are unsuitable.
Footing
The concrete base below the freeze line, wider than the foundation wall it supports.
Girder
The main horizontal carrying beam under the floor joists, resting on columns or piers.
Platform framing
Framing built one story at a time, each story's studs standing on a platform of joists and subfloor; the modern standard.
Pitch
A roof's vertical rise in inches per foot of horizontal span.
Flashing
Metal or other material covering joints where two building materials meet to keep water out.
R-Value
A measure of insulation's resistance to heat flow (R-Factor × amount of material); higher is better.
BTU
British thermal unit: the heat needed to raise one pound of water one degree Fahrenheit; used to size furnaces and air conditioners.
P-trap
The plumbing bend that holds a water seal so sewer gases cannot escape through a drain; replaced the older S-trap.
Amperage
The amount of electrical current flowing; residential service is a minimum of 100 amps, typically 200 in new construction.
CERCLA (Superfund)
The federal law governing cleanup of abandoned hazardous-waste sites; liability follows the property to new owners.
Environmental impact statement
The detailed study required under NEPA (federal) or SEQR (New York) for projects that may significantly affect the environment.
Friable
Easily crumbled; asbestos is hazardous when friable because fibers become airborne.
Title X
The Residential Lead-Based Paint Hazard Reduction Act requiring disclosure of known lead hazards in pre-1978 housing, the EPA pamphlet, and a 10-day inspection window.
External obsolescence
Loss of value caused by a more or less permanent nuisance or condition outside the property itself.

Practise this chapter

Flashcards (free) Practice exam

Read Chapter 9 in the Book

The Book comes with the Salesperson pass ($39 for 3 months).

A study course, in beta. This is not a New York State Department of State approved qualifying course, and the time you spend here does not count toward the 77 hours you need for a salesperson license. Take the 77-hour course at a DOS-approved school; use this to learn the material and to review it. · Powered by License to Earn LLC